00196478-08_MM_SX12DX12_en - 第65页
Major Maintenance 5.5.4 Final Work Maintenance Work on the Gantry Maintenance Manual SIPLACE SX1/SX2/DX1/DX2 65 5.5.3.8 5 . 5 . 3 . 8 R e p la c in g t h e L o o s e B e a r in g L u b r ic a t io n S y s t e m Y A x is …
Major Maintenance
Maintenance Work on the Gantry 5.5.3 Performing Maintenance Tasks
64 Maintenance Manual SIPLACE SX1/SX2/DX1/DX2
Head Mount from FS03 onwards:
► Remove the protective cap from the new lubrication adapter.
► Screw the new lubrication adapter hand-tight into place.
► Attach a maintenance label next to the lubrication adapter and write down the replacement day.
► Repeat these steps for all gantries.
See also
4.3.2.2 Cleaning the X Axis Loose Bearing and Contact Surface [ ➙ 30]
This lubrication adapter can be used on head mounts
from FS03 onwards. Only these head mounts have a suit-
able hole.
NOTICE!
All head mounts on SPS-capable machines have FS03 at
least.
► Remove the old lubrication adapter (1) with a slotted
screwdriver.
NOTICE!
Use a cable tie to fix any obstructing cables at the outside
of the conduit cable clip.
CAUTION!
Do not use any chemical cleaning agents!
► Use a SIPLACE cleaning tissue to wipe the loose
bearing (1) for the X axis and its contact surface (2) .
► Move the head mount twice over the entire length.
Now clean the running surfaces of the lubrication
adapter again.
CAUTION
Take care not to distort the felt insert.
Major Maintenance
5.5.4 Final Work Maintenance Work on the Gantry
Maintenance Manual SIPLACE SX1/SX2/DX1/DX2 65
5.5.3.8
5.5.3.8 Replacing the Loose Bearing Lubrication System Y Axis
Replacing the Loose Bearing Lubrication System Y Axis
See also
5.5.3.6 Cleaning the Y Axis Scale [ ➙ 62]
4.3.2.3 Cleaning the Y Axis Loose Bearing and Contact Surface [ ➙ 31]
5.5.3.4 Cleaning the Linear Guides of the Y Axis [ ➙ 62]
5.5.4
5.5.4 Final Work
Final Work
► For SW703.02 and higher only: switch the placement machine on and reset the maintenance cycle
counter for the relevant assemblies.
Overview of lubrication systems on the gantry
The lubrication systems are located on the loose bearing
side of the gantry! Each gantry has two lubrication sys-
tems.
► Unscrew the two lubrication systems (1) and (2) from
the gantry. One lubrication system is on the side fac-
ing you and the other one is on the side of the gantry
facing away from you.
► Use a dry cloth to clean the Y axis rollers, linear
guides and scales.
► Move the gantry twice over the entire length. Now
clean the Y axis rollers and linear guides again.
► Screw the protective caps off the new lubrication sys-
tems.
CAUTION!
Take care not to distort the felt insert.
► Screw the new lubrication systems hand-tight into
place.
► Repeat the procedure on the second gantry, if neces-
sary.
Major Maintenance
Maintenance Tasks for the Conveyor 5.6.1 Tools, Consumables, Spare and Wear Parts
66 Maintenance Manual SIPLACE SX1/SX2/DX1/DX2
5.6
5.6 Maintenance Tasks for the Conveyor
Maintenance Tasks for the Conveyor
5.6.1
5.6.1 Tools, Consumables, Spare and Wear Parts
Tools, Consumables, Spare and Wear Parts
▪ ESD wristband [00320279-xx]
▪ OIL Interflon Fin Super (teflon oil) [03017760-xx]
▪ Lint-free cleaning tissues [03082092-xx]
▪ Ethanol
Isopropanol – IPA can be used as an alternative.
▪ SIPLACE cleaning tissue [00315253-xx]
▪ Protective latex gloves [00372972-xx]
▪ Cotton gloves [00359087-xx]
5.6.2
5.6.2 Preparatory Steps
Preparatory Steps
Caution Conveyor - No PCB Must Be in the Conveyor
Note Co nveyor - Re commendation: Ad justing Sides via S oftware for Acces sibility
► Move the component trolley out of the machine.
See also
1.2 Preparatory Work... [ ➙ 12]
CAUTION
No board
There must be no PCBs in the machine during the following tasks.
NOTICE
Accessibility
We recommend using the following procedure for better access:
► Use the station software to adjust the conveyor sides in such a way that you can easily
reach all conveyor belts as well as the whole area below the sides.