SiplaceX4_en - 第448页

1 - 16 S tudent Guide SIPLACE X 9 Component handling Edition 09/2005 16 9.2.5 Optionally extension on the COT 9.2.5.1 T ape reel holder for the 3th reel at the 3x8mm S-Feeder When using 3x 8mm S-Feeder it would be necess…

100%1 / 670
1 - 15
Student Guide SIPLACE X
Edition 09/2005 9 Component handling
15
9.2.4 Adjustment the COT height
NOTE:The Adjustment of the COT height is in general identical for S- and X- tables.
This task requires 2 more persons to increase and decrease the COT height.
CAUTION:
Use always the eye-bolt to fix the component plate on the S-table, independend if you increase
or reduce the component table height, otherwise you may hurt your fingers.
Fig. 9.2 - 8 Adjusting the COT height
Legend
Increasing and reducing the COT height 9
➠ Attach the hooks of the lifting device to the eye-bolt (1) and fix the lifting plate (S-Table).
➠ For the X-Table the second person lift up the aluminum plate (table plate).
➠ Raise the component table top part until to rich the desired position of the height from the com-
ponent table.
➠ Then remove the 2 cotter pins (2) from the left and right sleeve shaft.
➠ Move the table plate in the correct height.
➠ Put back the 2 cotter pins (2) into the drilling hole of the sleeve shaft.
➠ Now, COT height is adjusted.
(1) Drilling hole for eye-bolt 2. Hole for the cotter pins
(1)
(2)
S- table
X- table
1 - 16
Student Guide SIPLACE X
9 Component handling Edition 09/2005
16
9.2.5 Optionally extension on the COT
9.2.5.1 Tape reel holder for the 3th reel at the 3x8mm S-Feeder
When using 3x8mm S-Feeder it would be necessary to install the tape reel holder for the3th pick
up track on the COT. The option allows unwinding of the tape easily and decrease machine
stoppage.
The adapter plate (Pos. 1) is fixed inside the COT with four screws. The adapter plate for the tape
reel holder will be mounted under the communication unit. In this mechanical device hang up the
holder for the 3th tape reel.
Fig. 9.2 - 9 Tape reel holder on the COT(left) / Mechanical device for the tape reel holder (right)
Legend
9.2.5.2 Additional reel holder of the X- table
The X-table has 40 tracks, but the reel container of the X- table allows only to put 30 reels on it,
so there exist optionally a additional reel holder.
Fig. 9.2 - 10 Additional reel holder X- table
(1) Adapter plate 2. Tape reel holder
3. Idler pulley, shortened
SMEMA 950 (max.19 inch)
Assembling the reel holder
SMEMA 930 (max.19 inch)
SMEMA 900 (max.17 inch)
SMEMA 830 (max.15 inch)
1 - 17
Student Guide SIPLACE X
Edition 09/2005 9 Component handling
17
9.2.5.3 Compressed air supply for Bulkcase feeder
Bulkcase feeder need for operation pressure air supply. So this pressure air supply is offered as
an option .
it is easy to mount. First remove the bung (Pos. 1) at pressure air hose in the feeder table (Pos.
2). Than the pneumatic supply for the bulck case feeder is mounted (Pos. 3) with 2 screws DIN
912, M8x20 (Pos. 4) on the component table (Pos. 2). At the rear side of the airkiss supply unit
are feeder clamps mounted (Pos. 5). This clamps keep the Bulkcase-feeder down correctly sealed
to the pressure air supply.
Fig. 9.2 - 11 Unit for bulkcase feeder
Legend
(1) Bung at component table 2. Componnent table
3. Pressure air supply for Bulkcase-Feeder 4. Screw DIN 912, M8x20
5. clamps for bulkcase feeder