sh030106u.pdf - 第141页
4. STA RTUP 4 - 16 (b) Posit ionin g operat ion Position ing oper ation ca n be per formed without using t he serv o system controller. Us e this operat ion with the forced sto p reset. This op eration may be used in dep…
4. STARTUP
4 - 15
4.5.1 Test operation mode in MR Configurator2
POINT
When the test operation mode is selected with the test operation select switch
(SW2-1), the SSCNET III/H communication for the servo amplifier in the test
operation mode and the following servo amplifiers is blocked.
(1) Test operation mode
(a) Jog operation
Jog operation can be performed without using the servo system controller. Use this operation with
the forced stop reset. This operation may be used independently of whether the servo is on or off
and whether the servo system controller is connected or not.
Exercise control on the jog operation screen of MR Configurator2.
1) Operation pattern
Item initial value Setting range
Speed [r/min] 200 0 to max. speed
Acceleration/deceleration
time constant [ms]
1000 0 to 50000
2) Operation method
When the check box of "Rotation only while the CCW or CW button is being pushed." is
checked.
Operation Screen control
Forward rotation start Keep pressing "Forward".
Reverse rotation start Keep pressing "Reverse".
Stop Release "Forward" or "Reverse".
Forced stop Click "Forced stop".
When the check box of "Rotation only while the CCW or CW button is being pushed." is not
checked.
Operation Screen control
Forward rotation start Click "Forward".
Reverse rotation start Click "Reverse".
Stop Click "Stop".
Forced stop Click "Forced stop".
4. STARTUP
4 - 16
(b) Positioning operation
Positioning operation can be performed without using the servo system controller. Use this operation
with the forced stop reset. This operation may be used independently of whether the servo is on or
off and whether the servo system controller is connected or not.
Exercise control on the positioning operation screen of MR Configurator2.
1) Operation pattern
Item initial value Setting range
Travel distance [pulse] 4000 0 to 99999999
Speed [r/min] 200 0 to max. speed
Acceleration/deceleration
time constant [ms]
1000 0 to 50000
Repeat pattern
Fwd. rot. (CCW) to
rev. rot. (CW)
Fwd. rot. (CCW) to rev. rot. (CW)
Fwd. rot. (CCW) to fwd. rot. (CCW)
Rev. rot. (CW) to fwd. rot. (CCW)
Rev. rot. (CW) to rev. rot. (CW)
Dwell time [s] 2.0 0.1 to 50.0
Number of repeats [time] 1 1 to 9999
2) Operation method
Operation Screen control
Forward rotation start Click "Forward".
Reverse rotation start Click "Reverse".
Pause Click "Pause".
Stop Click "Stop".
Forced stop Click "Forced stop".
(c) Program operation
Positioning operation can be performed in two or more operation patterns combined, without using
the servo system controller. Use this operation with the forced stop reset. This operation may be
used independently of whether the servo is on or off and whether the servo system controller is
connected or not.
Exercise control on the program operation screen of MR Configurator2. For details, refer to Help of
MR Configurator2.
Operation Screen control
Start Click "Start".
Pause Click "Pause".
Stop Click "Stop".
Forced stop Click "Forced stop".
(d) Output signal (DO) forced output
Output signals can be switched on/off forcibly independently of the servo status. Use this function for
output signal wiring check, etc. Exercise control on the DO forced output screen of MR
Configurator2.
4. STARTUP
4 - 17
(2) Operation procedure
1) Turn off the power.
2) Turn "ON (up)" SW2-1.
Set SW2-1 to "ON (up)".
ON
1234
1
ON
2 3 4
Turning "ON (up)" SW2-1 during power-on will not start the test operation mode.
3) Turn on the servo amplifier.
When initialization is completed, the decimal point on the first digit will blink.
After 1.6 s
After 0.2 s
Blinking
When an alarm or warning also occurs during the test operation, the decimal point on the first
digit will blink as follows.
After 0.8 s After 0.8 s
After 0.2 s
Blinking Blinking
4) Start operation with the personal computer.