Nordson_EFD_Automated_Dispensing_Systems_Maintenance_Guide - 第9页

9 www.nordsonefd.com info@nordsonefd.com +1-401-431-7000 Sales and service of Nordson EFD dispensing systems are available worldwide. Automated Dispensing Systems Maintenance & Parts Guide Linear Guideway Cleaning: Z…

100%1 / 42
Automated Dispensing Systems Maintenance & Parts Guide
8 www.nordsonefd.com info@nordsonefd.com +1-401-431-7000 Sales and service of Nordson EFD dispensing systems are available worldwide.
Linear Guideway Cleaning: ZAxis
NOTE: This procedure does not apply to R / RV Series units.
CAUTION
Risk of injury or equipment damage. Before performing any service procedure, complete the steps under
“Preparation for all Service Procedures” on page3.
Remove the ZAxis Cover (All Units Except R / RV Series)
1
a. Remove the four (4) screws that secure the
Zaxis cover to the Zaxis module.
b. Pull up vertically to remove the Zaxis cover.
NOTE: The Zaxis module can be in any
position along the Xaxis during maintenance.
Zaxis
cover
Zaxis module
(includes the cover
and the head)
Zaxis
head
a
b
a
Clean and Grease the ZAxis Linear Guideway
2
(All units except E2 / E2V)
Clean the Zaxis as follows:
a. With the Zaxis head in the top position,
reach behind the ball screw cover and use a
nonwoven cloth to clean any dust and grease
from the Zaxis linear guideway.
b. Pull the Zaxis head down to fully expose the
ball screw and the Zaxis linear guideway, then
use the nonwoven cloth to continue cleaning
dust and grease from the guide.
NOTE: Keep the Zaxis head in the bottom
position.
c. Use the brush and grease from the maintenance
grease kit to liberally apply grease to the Zaxis
linear guideway and to the ball screw. After they
are lubricated, release the Zaxis head from the
bottom position and move it up and down to
evenly disperse the grease and to ensure that it
travels smoothly on the Zaxis linear guideway.
d. If the Zaxis module does not travel easily, add
grease to the grease fitting on the Zaxis linear
guideway. Refer to “Applying Grease to the
Grease Fittings” on page12 for instructions.
Return here to continue.
e. Use a clean nonwoven cloth to remove excess
grease.
Ball screw
cover
Ball screw
a
b c
Continued on next page
9www.nordsonefd.com info@nordsonefd.com +1-401-431-7000 Sales and service of Nordson EFD dispensing systems are available worldwide.
Automated Dispensing Systems Maintenance & Parts Guide
Linear Guideway Cleaning: ZAxis (continued)
Clean and Grease the ZAxis Linear Guideway (continued)
3
(E2/E2V Series only)
Clean the Zaxis as follows:
a. Use a clean nonwoven cloth to clean any
dust and grease from the Zaxis linear
guideway.
b. Move the Zaxis head down to clean
previously inaccessible areas of the Zaxis
linear guideway.
c. Use the brush and grease from the
maintenance grease kit to liberally apply
grease to the Zaxis linear guideway.
Move the Zaxis module up and down to
spread the grease evenly and to ensure the
slide travels smoothly on the Zaxis linear
guideway.
d. If the Zaxis module does not travel easily,
add grease to the grease fitting on the Zaxis
linear guideway. Refer to “Applying Grease
to the Grease Fittings” on page12 for
instructions. Return here to continue.
ba
ZAxis
linear
guideway
c
Reinstall the ZAxis Cover (All Units Except R / RV Series)
4
a. Reinstall the Zaxis cover.
b. Secure the cover with the screws removed
previously.
b
a
b
Automated Dispensing Systems Maintenance & Parts Guide
10 www.nordsonefd.com info@nordsonefd.com +1-401-431-7000 Sales and service of Nordson EFD dispensing systems are available worldwide.
R / RV Series Ball Screw Cleaning: Z and R Axes
NOTE: This procedure applies only to R / RV Series units.
CAUTION
Risk of injury or equipment damage. Before performing any service procedure, complete the steps under
“Preparation for all Service Procedures” on page3.
Remove the ZAxis Cover (R / RV Series Only)
1
a. Remove the 10 screws that secure the
Zaxis cover to the Zaxis module.
b. Carefully pull up vertically to remove the
Zaxis cover.
NOTE: Removing the four (4) screws near
the bottom of the Zaxis cover releases
the Zaxis bottom plate; place your hand
underneath the plate to catch it.
NOTE: The Zaxis module can be in
any position along the Xaxis during
maintenance.
ba
Clean and Grease the ZAxis Components (R / RV Series Only)
2
Clean the Zaxis as follows:
a. Use a clean nonwoven cloth to clean any
dust and grease from the Zaxis ball screw,
spring, spring shaft, and Raxis ball spline.
b. Pull the Zaxis head down, exposing
all components listed above that were
previously inaccessible, and clean the dust
and grease with the nonwoven cloth.
NOTE: Keep the Zaxis head in the down
position.
c. Use the brush and grease from the
maintenance grease kit to liberally apply
grease to the Zaxis ball screw, spring,
spring shaft, and Raxis ball spline.
d. After greasing, release the Zaxis head from
the down position and move the Zaxis
module up and down to disperse the grease
evenly on each component.
e. Use a clean nonwoven cloth to remove
excess grease.
Raxis ball
spline
Spring on
spring shaft
Zaxis
ball screw
c
Continued on next page