GDM 13-34切石基说明书.pdf - 第9页
English | 9 Bosch Power Tools 1 609 9 2A 41D | ( 26.9.17) Cutting Marks The 0 ° cutting mark ( 7 ) indicates the position of the diamond cutting disc for ri ght-angled cuts. The 45 ° cutting mark ( 8 ) in- dicates the po…
8 | English
1 609 92A 41D | (26.9.17) Bosch Power Tools
Technical Data
Assembly
Before any work on the machine itself, pull the mains
plug.
Dust Extraction
Dust from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one’s health. Touching or breathing-in the dust can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dust, such as oak or beech dust, is considered car-
cinogenic, especially in connection with wood-treatment
additives (chromate, wood preservative). Materials con-
taining asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
Mounting/Replacing the Diamond Cutting Disc
(see figure A)
When mounting and replacing diamond cutting discs, it
is recommended to wear protective gloves.
Diamond cutting discs become very hot during opera-
tion; do not touch them until they have cooled down.
Always use a correctly sized diamond cutting disc with
the fitting mounting hole that corresponds with the
information listed in the technical data.
Use only diamond-tipped cutting discs. Segmented
diamond wheels may only have negative cutting angles
and slots between the segments to a maximum of
10 mm.
Mounting the Diamond Cutting Disc
Clean the diamond cutting disc 15 and all clamping parts to
be mounted.
Mount the mounting flange 14 onto the drive spindle 13.
Place the diamond cutting disc 15 onto the mounting flange
14. The direction arrow on the diamond cutting disc 15 and
the direction-of-rotation arrow on the blade guard 6 must
correspond.
Mount the clamping flange 16 and screw in the clamping bolt
18.
Hold the clamping flange 16 with the ring spanner 17 and
tighten the clamping bolt 18 with the hex key 19.
Removal of the Diamond Cutting Disc
Hold the clamping flange 16 with the ring spanner 17 and
loosen the clamping bolt 18 with the hex key 19.
Remove the clamping flange 16 and diamond cutting disc 15
from the drive spindle 13.
Operation
Operating Modes
Before any work on the machine itself, pull the mains
plug.
Adjusting the Cutting Angle (see figure B)
Loosen wing bolt 9. Tilt the machine sidewards until the de-
sired cutting angle is set on the scale 11. Tighten wing bolt 9
again.
Note: For bevel cuts, the cutting depth is smaller than the
setting indicated on the cutting-depth scale 3.
Pre-selecting the Cutting Depth (see figure C)
The cutting depth may only be pre-selected when the
machine is switched off.
Adapt the cutting depth to the thickness of the workpiece. For
optimum results, the diamond cutting disc must protrude
approx. 2 mm out of the material.
Loosen wing bolt 4. For a smaller cutting depth, pull the
machine from the base plate 10; for a larger cutting depth,
push the machine toward the base plate 10. Adjust the
desired cutting depth at the cutting-depth scale 3. Tighten
wing bolt 4 again.
Masonry Saw GDM 13-34 GDM 13-34
Article number
3 601 36A 2.. 3 601 36A 2B0
Rated power input
W13001300
Rated speed
min
-1
12000 12000
Max. diameter for diamond cutting discs
mm 114 114
Cutting discs width, min.
mm 1.6 1.6
Cutting discs width, max.
mm 2.4 2.4
Mounting bore
mm 20 15
Cutting depth, max.
–for 0° bevel angle
–for 45° bevel angle
mm
mm
34
22
34
22
Weight according to EPTA-Procedure 01:2014 kg 2.8 2.8
Protection class
/II /II
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
OBJ_BUCH-936-006.book Page 8 Tuesday, September 26, 2017 12:39 PM
English | 9
Bosch Power Tools 1 609 92A 41D | (26.9.17)
Cutting Marks
The 0° cutting mark (7) indicates the position of the diamond
cutting disc for right-angled cuts. The 45° cutting mark (8) in-
dicates the position of the diamond cutting disc for 45° cuts.
Starting Operation
Observe correct mains voltage! The voltage of the
power source must agree with the voltage specified on
the nameplate of the machine. Power tools marked
with 230 V can also be operated with 220 V.
Products sold in AUS and NZ only: Use a residual current
device (RCD) with a rated residual current of 30 mA or less.
Switching On and Off
To start the machine, press the On/Off switch 1 and keep it
pressed.
To lock the pressed On/Off switch 1, press the lock-on button
2.
To switch off the machine, release the On/Off switch 1 or
when it is locked with the lock-on button 2, briefly press the
On/Off switch 1 and then release it.
Check the diamond cutting discs before use. The dia-
mond cutting disc(s) must be mounted properly and be
able to rotate freely. Carry out a test run for at least one
minute without any load. Do not use diamond cutting
discs that are damaged, out-of-balance, or vibrate.
Damaged diamond cutting discs can rupture and lead to
injuries.
Working Advice
Exercise caution when cutting slots in structural walls;
see Section “Information on Structures”.
Do not strain the machine so heavily that it comes to a
standstill.
After heavily straining the power tool, continue to run
it at no-load for several minutes to cool down the acces-
sory.
For cutting-depths greater than 20 mm in hard materi-
als, e.g., concrete, apply several worksteps so that the
motor is not overloaded.
Clamp the workpiece if it does not remain stationary
due to its own weight.
The machine may only be used for dry cutting.
Diamond cutting discs become very hot during opera-
tion; do not touch them until they have cooled down.
Protect the cutting disc against impact, shock and grease. Do
not subject the cutting disc to lateral pressure.
Do not brake coasting diamond cutting discs by applying side-
ward pressure.
For cutting especially hard material, e. g., concrete with high
pebble content, the diamond cutting disc can overheat and
become damaged as a result. This is clearly indicated by
circular sparking, rotating with the diamond cutting disc.
In this case, interrupt the cutting process and allow the dia-
mond cutting disc to cool by running the machine for a short
time at maximum speed with no load.
Noticeably decreasing work progress and circular sparking
are indications of a diamond cutting disc that has become
dull. Briefly cutting into abrasive material (e.g. lime-sand
brick) can resharpen the disc again.
Direction of Cut (see figure D)
The machine must always work in an up-grinding motion.
Otherwise, the danger exists of it being pushed uncontrolled
out of the cut.
Parallel Guide (see figure E)
The parallel guide 21 enables exact cuts along a workpiece
edge and cutting strips of the same dimension.
Loosen wing bolt 20 and slide the scale of the parallel guide
21 through the guide in the base plate 10. Adjust the desired
cutting width as the scale setting at the respective cutting
mark 7 or 8; see Section “Cutting Marks”. Tighten wing bolt
20 again.
Information on Structures
Slots in structural walls are subject to the Standard DIN 1053
Part 1, or country-specific regulations.
These regulations are to be observed under all circumstanc-
es. Before beginning work, consult the responsible structural
engineer, architect or the construction supervisor.
Maintenance and Service
Maintenance and Cleaning
Before any work on the machine itself, pull the mains
plug.
For safe and proper working, always keep the machine
and ventilation slots clean.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in
order to avoid a safety hazard.
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can
also be found under:
www.bosch-pt.com
Bosch’s application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the nameplate of
the product.
Cambodia
Robert Bosch (Cambodia) Co., Ltd
Unit 8BC, GT Tower, 08th Floor, Street 169,
Czechoslovakia Blvd, Sangkat Veal Vong
Khan 7 Makara, Phnom Penh
VAT TIN: 100 169 511
Tel.: +855 23 900 685
Tel.: +855 23 900 660
www.bosch.com.kh
OBJ_BUCH-936-006.book Page 9 Tuesday, September 26, 2017 12:39 PM
10 | English
1 609 92A 41D | (26.9.17) Bosch Power Tools
People’s Republic of China
China Mainland
Bosch Power Tools (China) Co., Ltd.
567, Bin Kang Road
Bin Jiang District 310052
Hangzhou, P.R.China
Tel.: 4008268484
Fax: (0571) 87774502
E-Mail: contact.ptcn@cn.bosch.com
www.bosch-pt.com.cn
HK and Macau Special Administrative Regions
Robert Bosch Co. Ltd.
21st Floor, 625 King’s Road
North Point, Hong Kong
Customer Service Hotline: +852 2101 0235
Fax: +852 2590 9762
E-Mail: info@hk.bosch.com
www.bosch-pt.com.hk
India
Bosch Service Center
69, Habibullah Road, (Next to PSBB School), T. Nagar
Chennai–600077
Phone: (044) 64561816
Bosch Service Center Rishyamook
85A, Panchkuin Road
New Delhi–110001
Phone: (011) 43166190
Bosch Service Center
79, Crystal Bldg., Dr. Annie Besant Road, Worli
Mumbai–400018
Phone: (022) 39569936 / (022 )39569959 /
(022) 39569967 / (022) 24952071
Indonesia
PT Robert Bosch
Palma Tower 10
th
Floor
Jalan RA Kartini II-S Kaveling 6
Pondok Pinang, Kebayoran Lama
Jakarta Selatan 12310
Tel.: (21) 3005-5800
www.bosch-pt.co.id
Malaysia
Robert Bosch Sdn. Bhd.(220975-V) PT/SMY
No. 8A, Jalan 13/6
46200 Petaling Jaya
Selangor
Tel.: (03) 79663194
Toll-Free: 1800 880188
Fax: (03) 79583838
E-Mail: kiathoe.chong@my.bosch.com
www.bosch-pt.com.my
Pakistan
Robert Bosch Middle East FZE – Pakistan Liaison Office
2nd Floor Plaza # 10, CCA Block, DHA Phase 5
Lahore, 54810
Phone: +92(303)4444311
Email: Faisal.Khan@bosch.com
Philippines
Robert Bosch, Inc.
28th Floor Fort Legend Towers,
3rd Avenue corner 31st Street,
Fort Bonifacio, Global City,
1634 Taguig City
Tel.: (632) 8703871
Fax: (632) 8703870
www.bosch-pt.com.ph
Singapore
Powerwell Service Centre Ptd Ltd
Bosch Authorised Service Centre (Power Tools)
4012 Ang Mo Kio Ave 10, #01-02 TECHplace
Singapore 569628
Tel.: 6452 1770
Fax: 6452 1760
E-Mail: ask@powerwellsc.com
www.powerwellsc.com
www.bosch-pt.com.sg
Thailand
Robert Bosch Ltd.
Liberty Square Building
No. 287, 11 Floor
Silom Road, Bangrak
Bangkok 10500
Tel.: 02 6393111
Fax: 02 2384783
Robert Bosch Ltd., P. O. Box 2054
Bangkok 10501
www.bosch.co.th
Bosch Service – Training Centre
La Salle Tower Ground Floor Unit No.2
10/11 La Salle Moo 16
Srinakharin Road
Bangkaew, Bang Plee
Samutprakarn 10540
Tel.: 02 7587555
Fax: 02 7587525
Vietnam
Branch of Bosch Vietnam Co., Ltd in HCMC
Floor 10, 194 Golden Building
473 Dien Bien Phu Street
Ward 25, Binh Thanh District, Ho Chi Minh City
Tel.: (08) 6258 3690
Fax: (08) 6258 3692
Hotline: (08) 6250 8555
www.bosch-pt.com.vn
Armenia, Azerbaijan, Georgia, Kyrgyzstan, Mongolia,
Tajikistan, Turkmenistan, Uzbekistan
TOO “Robert Bosch” Power Tools, After Sales Service
Rayimbek Ave., 169/1
050050, Almaty, Kazakhstan
Service Email: service.pt.ka@bosch.com
Official Website: www.bosch.com, www.bosch-pt.com
OBJ_BUCH-936-006.book Page 10 Tuesday, September 26, 2017 12:39 PM