00197454-01_AI_Portal_40mm_TwinVHF_SX12_de_en - 第106页
assembly Gantry Preparations 3.2.3 Locking and Transporting the Ga ntry Carrier 106 Reconfiguration Kit Twin VHF with Gantry Reconfiguration Ki t T w i n V H F m i t P o r - 3.2.3 3 . 2 . 3 L o c k in g a n d T r a n s p…
assembly
3.2.2 Unpacking the Gantry Gantry Preparations
Reconfiguration Kit Twin VHF with Gantry Reconfiguration Kit Twin VHF mit Portal 105
3.2.2
3.2.2 Unpacking the Gantry
Unpacking the Gantry
Transportation crate
The gantry is packed in a transportation crate. Move the
transportation crate near to the SIPLACE SX machine on
which the gantry is to be assembled. Do not move the
gantry over long distances with the gantry lift.
► Open the turn-lock fasteners (3) on the top (1) and
front (2) of the transportation crate.
► Remove the two wooden panels at (1) and (2).
NOTICE!
The gantry is fixed with 4 screws in the transportation
crate.
CAUTION!
Carrier
When putting back the carrier it must be screwed again.
Move the gantry lift into position
► Carefully move the transportation lift (1) up to the
gantry.
CAUTION!
Take care not to damage the gantry when moving it with
the gantry lift
Do not hit the gantry or locks with the gantry carrier plate
(3).
Make sure that the gantry carrier plate (3) protrudes
above the gantry carrier locks (4).
► Remove the foam cover (2).
assembly
Gantry Preparations 3.2.3 Locking and Transporting the Gantry Carrier
106 Reconfiguration Kit Twin VHF with Gantry Reconfiguration Kit Twin VHF mit Por
-
3.2.3
3.2.3 Locking and Transporting the Gantry Carrier
Locking and Transporting the Gantry Carrier
The "gantry 40 mm" may only be transported with the current gantry carriers [00519814-03] (observe
function state!).
Move the gantry lift to the gantry
Locking the gantry carrier
► Move the gantry carrier plate (2) for the gantry lift over
the gantry carrier locks (3). The groove (1) must be
able to engage with the two locking plates (3).
► Lower the gantry lift so that the gantry carrier plate
can slide into the locks (4).
► Move the lift only so far down that the locking lever (5)
can be closed.
► Press the lock (4) back and pull (1) the handle (2) of
the lock upwards.
⇨ The lever (3) will engage. The spring on the lock (4)
secures the locking mechanism.
assembly
3.2.3 Locking and Transporting the Gantry Carrier Gantry Preparations
Reconfiguration Kit Twin VHF with Gantry Reconfiguration Kit Twin VHF mit Portal 107
Locking the gantry carrier correctly
Securing the gantry in the transportation crate
► Check that the lever (2) on the lock (1) has engaged
properly.
► To open, press the lock backwards and then press
the lever downwards. This opens the lock.
► The gantry is fixed with 4 screws (1) in the transpor
-
tation crate. Loosen these screws.
CAUTION!
Only transport the gantry with the gantry lift when the
arms are locked!
► Move the gantry lift upwards and carefully lift the gan
-
try out of the transportation crate.
NOTICE!
The placement head must be in the center of the gantry.
This ensures that the load is distributed evenly during
transportation.