00197454-01_AI_Portal_40mm_TwinVHF_SX12_de_en - 第112页
assembly Fitting the Gantry 3.2.5 Fitting the HCUs a nd HCU Base Adapter 112 Reconfiguration Kit Twin VHF with Gantry Reconfiguration Ki t T w in V H F m i t P o r - 3.5 3 . 5 F it t in g t h e G a n t r y Fitting the Ga…
assembly
3.2.5 Fitting the HCUs and HCU Base Adapter Converting the Cover
Reconfiguration Kit Twin VHF with Gantry Reconfiguration Kit Twin VHF mit Portal 111
► Connect the head boards with the HCU head adapter, using 2 flat ribbon cables in each case.
See also
1.2 Preparatory Work... [ ➙ 76]
3.4
3.4 Converting the Cover
Converting the Cover
When using the WPC5/6 for high components, you need to convert the cover. The new cover has a re
-
cess for the WPC on the disk.
Proceed as follows:
CAUTION
No WPC
If no WPC is fitted, you will not be able to feed in components with a height of 40 mm.
The cover may not be converted if there is no WPC.
1. Cover.
2. Hinges on the cover (2x)
CAUTION!
You may need to enlist the help of a second person for
this job.
► Loosen the screws fastening the hinges at the top of
the cover. While doing this, hold the front section of
the cover tight.
► Remove the front section of the cover.
► Insert the new front section of the cover into the ma
-
chine and screw into place.
1. Danger of crushing label (2x)
2. Barcode adhesive label
► Attach the following adhesive labels to the new cover.
For their exact positions, refer to the old cover.
assembly
Fitting the Gantry 3.2.5 Fitting the HCUs and HCU Base Adapter
112 Reconfiguration Kit Twin VHF with Gantry Reconfiguration Kit Twin VHF mit Por
-
3.5
3.5 Fitting the Gantry
Fitting the Gantry
Hooking the gantry carrier into place on the machine
► (1) Use the gantry lift to move the gantry in front of the
machine location.
CAUTION!
Move the gantry carefully
Make sure that you do not damage the monitor (3).
Make sure that you do not hit the gantry anywhere and do
not move it too far into the machine (2). Always check the
right and left sides.
1. Docking hook on the gantry carrier
2. Docking unit on the machine linear guides
► Move the gantry forwards so that the gantry carrier
docking hooks (1) are in front of the machine docking
unit (2).
► Always check the right and left sides.
► Lift the gantry so that the gantry carrier docking hooks
(1) are above the machine docking unit (2).
► Carefully lower the gantry so that the two docking
hooks (1) slide reliably into the openings in the dock
-
ing unit (2).
► Always check the right and left sides.
assembly
3.2.5 Fitting the HCUs and HCU Base Adapter Fitting the Gantry
Reconfiguration Kit Twin VHF with Gantry Reconfiguration Kit Twin VHF mit Portal 113
Remove the tilt guard and move in the gantry
The docking hooks are hooked into place on the left (1)
and right (2) sides.
The gantry carrier with the gantry is now fixed reliably
onto the machine.
► Open the tilt guard (1).
► Push the gantry (2) into the machine so that both
sides of the gantry rest on the two linear guides.
► Move the gantry lift with the gantry carrier out of the
location.
► Move the gantry (2) into the machine so that the trail
-
ing cable (1) can be pulled underneath, through the
gantry.