00197454-01_AI_Portal_40mm_TwinVHF_SX12_de_en - 第79页

Introduction 1.3.4 Release History Other Instructions Reconfiguration Kit Twin VHF with Gantry Re configuration Kit Twin VHF mit Portal 79 1.3.3.3 1 . 3 . 3 . 3 H a n d lin g E S D M o d u le s Handling ESD Modules Do no…

Introduction

Other Instructions 1.3.1 Environmentally-Friendly Disposal of Materials and Components

78 Reconfiguration Kit Twin VHF with Gantry Reconfiguration Kit Twin VHF mit Por

1.3

1.3 Other Instructions

Other Instructions

1.3.1

1.3.1 Environmentally-Friendly Disposal of Materials and Components

Environmentally-Friendly Disposal of Materials and Components

SIPLACE products are manufactured using only materials and parts that can be easily separated and

disposed of in an environmentally-friendly way.

1.3.2

1.3.2 Use of Original SIPLACE Accessories and Spare Parts

Use of Original SIPLACE Accessories and Spare Parts

Only use original spare parts and authorized accessories. The use of other parts will affect safety and

will invalidate the liability for any consequential damage.

1.3.3

1.3.3 ESD Guidelines

ESD Guidelines

1.3.3.1

1.3.3.1 Definition of ESD

Definition of ESD

1.3.3.2

1.3.3.2 Important Measures to Protect Against Static Charging

Important Measures to Protect Against Static Charging

► Most plastics can easily become charged and must therefore be kept away from at-risk components.

► Always ensure that people, the workplace and packaging are safely earthed when handling electro

static sensitive components.

NOTICE

Observe the applicable regulations

The company operating the system has sole responsibility for the proper, environmentally-

friendly disposal of machines, working materials, consumables and wear parts.

► Please observe your national statutory provisions for waste disposal and environmental

protection.

Almost all of the modules in use today are equipped with highly integrated MOS blocks and compo

nents. The manufacturing techniques used mean that these electronic components are extremely sen

sitive to overvoltage and thus to electrostatic discharge.

The abbreviation for such modules is 'ESD' (Electrostatic Sensitive Device). This is

used internationally, although the German abbreviation 'EGB' may also be seen. The

following symbol on cabinet rating plates, racks or packaging indicates that compo

nents which are sensitive to electrostatic discharge have been used and thus that the

modules concerned are also touch-sensitive.

ESDs can be destroyed by voltages and power levels that are far below the level that can be perceived

by humans. Such voltages occur if a person touches a component or module without earthing them

selves. Components that are exposed to such overvoltages do not generally appear to be defective im

mediately - incorrect behavior starts after the component or module has been in operation for some

time.

Introduction

1.3.4 Release History Other Instructions

Reconfiguration Kit Twin VHF with Gantry Reconfiguration Kit Twin VHF mit Portal 79

1.3.3.3

1.3.3.3 Handling ESD Modules

Handling ESD Modules

Do not touch electronic modules unless it is absolutely essential to do so in order to carry out other work.

If it is necessary, make sure that you do not touch the pins or printed conductors when you pick up flat

modules.

Do not touch components unless

▪ You are constantly earthed by an ESD wrist strap or

▪ You are wearing ESD shoes or ESD shoe earthing strips on an ESD floor.

Always discharge yourself before you touch an electronic module. To do this, simply touch a conductive

and earthed object immediately before you touch the module (such as unpainted parts of a switch cab

inet, a water pipe, etc.).

Do not allow modules with chargeable and highly insulating materials to touch one another, e.g. plastic

films, insulating table surfaces or items of clothing made from synthetic fibers.

Always place the modules on a conductive surface (table with an ESD coating, conductive ESD foam,

ESD bag or container).

Do not bring modules near visual display units, monitors or televisions. Keep them at least 10 cm away

from the screen.

1.3.3.4

1.3.3.4 Measurements and Modifications to ESD Modules

Measurements and Modifications to ESD Modules

Measurements of the assemblies may only be taken if

▪ The measuring device has been grounded (e.g. via protective conductor) or

▪ The measuring head of the potential-free measuring device has been briefly discharged before

measurement (e.g. touching blank metal control unit housing).

► Always use an earthed soldering iron if you carry out any soldering work.

1.3.3.5

1.3.3.5 Dispatching ESD Modules

Dispatching ESD Modules

► Always store modules and components in conductive packaging (e.g. metallized plastic bags or met

al sleeves) and dispatch them in conductive packaging.

► If the packaging is not conductive, place the modules in a conductive envelope before packaging.

Use conductive foam rubber, ESD bags, domestic aluminum foil or paper, for example. NEVER use

plastic bags or film.

► If the module has integral batteries, ensure that the conductive packaging does not touch or short-

circuit the battery terminals and, if necessary, first cover the terminals with insulating tape or mate

rial.

1.3.4

1.3.4 Release History

Release History

Document

SIPLACE SX1/SX2 V2

Reconfiguration Kit Twin VHF with gantry

Assembly instructions

Release Changes

11/2013 First edition

Introduction

Abbreviations 1.3.5 SIPLACE on the World Wide Web (WWW)

80 Reconfiguration Kit Twin VHF with Gantry Reconfiguration Kit Twin VHF mit Por

1.3.5

1.3.5 SIPLACE on the World Wide Web (WWW)

SIPLACE on the World Wide Web (WWW)

Log into our SIPLACE

homepage at http://www.siplace.com.

► You can choose between the German and English versions.

The different sections contain information about our products, services and contact persons.

In addition, registered customers can also access the

SIPLACE User Group

. Here you can call up spe

cial information about our placement systems e.g.

▪ Technical documentation,

▪ Technical information,

▪ Spare parts lists etc.

Registration for the user group is very simple:

► Click on the Register link.

► Fill in the registration form and send it off to us.

Soon afterwards, you will receive your access authorization with USER ID and password.

1.4

1.4 Abbreviations

Abbreviations

Abbreviations Description

PA Placement area

CO Component

COT Changeover table

COT-i Changeover table insert

C&P Collect&Place

C&P12, CP12 Collect&Place head with 12 segments

C&P20, CP20 Collect&Place head with 20 segments

C&P6, CP6 Collect&Place head with 6 segments

CoD Capacity on Demand

CPP Collect&Pick&Place head

CPx Collective term for CPP, CP20, CP12 and/or CP6

ESD Electrostatic sensitive device

EMC Electromagnetic compatibility

FHE Fast Head Exchange

LBO Long Board Option

PCB Board

P&P Pick&Place

TH TwinHead