EUKYX-199-4110_G5S2_Instruction_Vol4_E - 第133页
EUKYX 2-4 199-4100 2.2 Management Information list Code D isp lay Ar ea A Di spl ay Are a B 1 0d0 1 Pat tern p rogr am is abnormal Plea se set t he nor mal p at tern pr ogr am 1 0e0 1 Prod Ch ng is no t read y Conveyo r …
EUKYX
2-3199-4100
2.2 Management Information list
Code Display Area A Display Area B
10101 Emergency Stop Press [POWER ON] button to activate Load Power circuit.
10103 Emergency Stop Emergency Stop switch is pressed. Please cancel it.
10201 Air Pressure Drop Air Pressure Drop is detected
10401
Safety cover lock
confirm
Please close and lock the safety cover.
10402
Safety cover lock
confirm
Operate it after close and lock the safety cover.
10403
Safety cover lock
confirm
Operate after close and lock the safety cover.
10404
Safety cover lock
confirm
The safety cover is in unlock. Please complete to unlock and operate
it.
10503
Beam XY main circuit
OFF
Beam XY main circuit Error
10801
Feeder base confirm
(Block1)
Set the feeder cart (Block1) and connect cable.
10802
Feeder base confirm
(Block1)
Cannot set Feeder Cart downward to detect Elevator Unit (Block1).
Operate after remove it .
10803
Feeder base confirm
(Block1)
Elevator Unit (Block1) is not connected. Please connect to it with "Unit
Exchange Menu".
10804
Feeder base confirm
(Block1)
Batch Connector of Elevator Unit (Block1) is not connected. Please
check connection.
10805
Feeder base confirm
(Block1)
Feeder cart (Block1) is not upper position. Push Feeder Ready Switch.
10806
Feeder base confirm
(Block1)
Push Feeder Ready SW.
10807
Feeder base confirm
(Block1)
Feeder base power or Feeder power is "OFF". Please press "Feeder
Ready" switch (Block1), and put it up again after putting Feeder Cart
(Block1) down.
10901
Feeder base confirm
(Block2)
Set the feeder cart and connect cable. (Block2)
10902
Feeder base confirm
(Block2)
Cannot set Feeder Cart downward to detect Elevator Unit (Block2).
Operate after remove it.
10903
Feeder base confirm
(Block2)
Elevator Unit (Block2) is not connected. Please connect to it with "Unit
Exchange Menu".
10904
Feeder base confirm
(Block2)
Batch Connector of Elevator Unit (Block2) is not connected. Please
check connection.
10905
Feeder base confirm
(Block2)
Feeder cart (Block2) is not upper position. Push feeder ready sw.
10906
Feeder base confirm
(Block2)
Push feeder ready sw.
10907
Feeder base confirm
(Block2)
Feeder base power or Feeder power is "OFF". Please press "Feeder
Ready" switch (Block2), and put it up again after putting Feeder Cart
(Block2) down.
10b01
Feeder is not ready
(Block1)
Please turn on the Feeder Ready SW (Block1).
10c01
Feeder is not ready
(Block2)
Please turn on the Feeder Ready SW (Block2).
2.2 Management Information list
The following is the management information list by code.
EUKYX
2-4199-4100
2.2 Management Information list
Code Display Area A Display Area B
10d01
Pattern program is
abnormal
Please set the normal pattern program
10e01 Prod Chng is not ready
Conveyor width does not fit production data. Execute conveyor width
setup.
110 01 Empty Feeder (Block1) Please set the feeder (Block1) that used by the pattern program.
11101 Empty Feeder (Block2) Please set the feeder (Block2) that used by the pattern program.
11201
Stock Stick Feeder
(Block1)
A setup of a stock stick unit and part library data is not in agreement.
Please carry that whose discernment ID of a part library / supply data
and ID on the rear surface of a unit correspond.
11202
Stock Stick Feeder
(Block1)
Please check the value of the thickness data t and Ut of a part library.
11301
Stock Stick Feeder
(Block2)
A setup of a stock stick unit and part library data is not in agreement.
Please carry that whose discernment ID of a part library / supply data
and ID on the rear surface of a unit correspond.
1130 2
Stock Stick Feeder
(Block2)
Please check the value of the thickness data t and Ut of a part library.
11401 Zeroing not finish Perform All zeroing
11402 Zeroing not finish Perform All zeroing
11403 Zeroing not finish Perform All zeroing
11404 Zeroing not finish Perform All zeroing
1140 5 Zeroing not finish Perform All zeroing
1140 6 Zeroing not finish Motor is not servo on. Perform All zeroing
11701 PCB positioning Please position the PCB.
1170 2 PCB positioning Set Pos PCB [Output Position].
1170 3 PCB positioning Set Pos PCB [Input Position].
1170 4 PCB positioning Please cancel PCB positioning after cancelling operation.
1170 5 PCB positioning Please set PCB positioning [Input or Output] of [Lane A]
1170 6 PCB positioning Please set PCB positioning. [Output position] of [Lane A].
11707 PCB positioning Please set PCB positioning [Input position] of [Lane A].
1170 8 PCB positioning Please set PCB Positioning [Input or Output] of [Lane B].
1170 9 PCB positioning Please set PCB Positioning [Output position] of [Lane B].
1170 a PCB positioning Please set PCB positioning [Input position] of [Lane B].
1170 b PCB positioning Please set PCB positioning of input position on PCB transfer menu.
1170 c PCB positioning
Please set PCB positioning of [Lane A] input position on PCB transfer
menu.
1170 d PCB positioning
Please set PCB positioning of [Lane B] input position on PCB transfer
menu.
1170 e PCB positioning
Board has been positioned inside the unit two. For finishing, please
run it from an upstream position positioning sequentially one by one.
11901
Head unsettled comp.
confirmation
An unsettled component was detected. Please discard the component.
In case of the "Pauses" condition, perform the operation for
interruption.
11a01
Nozzle stocker lower
limit confirmation
Please perform All zeroing.
11c 01
Nozzle arrangement
confirmation
The nozzle arrangement of the Current Program differs from it of Head.
EUKYX
2-5199-4100
2.2 Management Information list
Code Display Area A Display Area B
11c 02
Nozzle arrangement
confirmation
A nozzle cannot be stored. Please check the following. (Block 1)
1. Existence of Nozzle Stocker, Clamp Condition
2. Nozzle Configuration Data
11c 03
Nozzle arrangement
confirmation
A nozzle cannot be stored. Please check the following. (Block 2)
1. Existence of Nozzle Stocker, Clamp Condition
2. Nozzle Configuration Data
11c 04
Nozzle arrangement
confirmation
The nozzles to be used are insufficient. Please check the following.
(Block 1)
1. Existence of Nozzle Stocker, Clamp Condition
2. Nozzle Configuration Data
11c 05
Nozzle arrangement
confirmation
The nozzles to be used are insufficient. Please check the following.
(Block 2)
1. Existence of Nozzle Stocker, Clamp Condition
2. Nozzle Configuration Data
11c 0 6
Nozzle arrangement
confirmation
The nozzle placement of the head to assist for is different. (Head2)
11c 07
Nozzle arrangement
confirmation
The nozzle placement of the head to assist for is different. (Head1)
11c 08
Nozzle arrangement
confirmation
The Nozzle used is insufficient for assist. Please arrange the Nozzle
used.
11c 09
Nozzle arrangement
confirmation
Nozzle placement of Nozzle Stocker is short, the sequence that cannot
change a nozzle for exists. Please confirm nozzle stocker placement.
11c 0a
Nozzle arrangement
confirmation
A nozzle exists on Nozzle Stocker, but the sequence that cannot
change a nozzle for by the limitation of the head exists. Please confirm
nozzle stocker placement.
12a01
Tray shortage Comp
(Block1)
Please supply Tray Cmpnt, close Tray Safety door and push Tray
Ready SW (Block1).
12a02
Tray shortage Comp
(Block1)
There is the shortage components. Please supply the components.
12b01
Tray shortage Comp
(Block2)
Please supply Tray Cmpnt, close Tray Safety door and push Tray
Ready SW (Block2).
12b02
Tray shortage Comp
(Block2)
There is the shortage components. Please supply the components.
12c01
Tray is not ready
(Block1)
Error signal of the unit is detected.\r\n(1) Please supply the
components. (2) Please close elevator loading door.\r\n(3) Please
press a reset button. (4) Please release Inhibit button.
12d01
Tray is not ready
(Block2)
Error signal of the unit is detected.\r\n(1) Please supply the
components. (2) Please close elevator loading door.\r\n(3) Please
press a reset button. (4) Please release Inhibit button.
13101 Feeder set Err
A pickup miss comp is detected. (Block1) Please open the safety door
and confirm whether pickup miss comp is dropped. If the comp is
dropped, there is a possibility of interference with Head. A detection
state can be checked on a control screen.
13102 Feeder set Err
The feeder latch worked off. (Block1)
Please close the hook of a feeder. A detection state can be checked
on a control screen.
13103 Feeder set Err
A pickup miss comp is detected. (Block2) Please open the safety door
and confirm whether pickup miss comp is dropped. If the comp is
dropped, there is a possibility of interference with Head. A detection
state can be checked on a control screen.
13104 Feeder set Err
Feeder Latch worked off. (Block2)
Please close the hook of a feeder. A detection state can be checked
on a control screen.
13105 Feeder set Err Not connect selected Feeder.