EUKYX-199-4110_G5S2_Instruction_Vol4_E - 第261页

EUKYX 3-96 199-4100 3.8 Automatic Adjustment Error ID Error Name, Description, Cause, and Remed y 4 9 6 715 Conveyo r Wid th W3 Erro r Over-c urren t in Conveyo r Wid th W3 Erro r in Moto r out put li ne. Chec k out t he…

100%1 / 363
EUKYX
3-95199-4100
3.8 Automatic Adjustment
Error ID Error Name, Description, Cause, and Remedy
49661b Error of Shuttle Conveyor width W2 in Output side
-----
Reserved Function of driver. Please make inquiries when error is detected.
49661c Error of Shuttle Conveyor width W2 in Output side
-----
Reserved Function of driver. Please make inquiries when error is detected.
49661d Error of Shuttle Conveyor width W2 in Output side
-----
Reserved Function of driver. Please make inquiries when error is detected.
49661e Error of Shuttle Conveyor width W2 in Output side
-----
Reserved Function of driver. Please make inquiries when error is detected.
49661f Error of Shuttle Conveyor width W2 in Output side
System Error in Conveyor Width W2.
System Error of internal driver. Driver error is supposed if this problem happens frequently.
496701 Conveyor Width W3 Error
Drive Alarm during Conveyor Width W3 axial operation.
Confirm reset Method of detailed Sub-system error counts of Alarm.
496702 Conveyor Width W3 Error
Conveyor Width W3-axis could not start
A state in which the operating command is not normally accepted.
1. Confirm connection to communication cable.
2. Confirm Power supply(24V).
3. Confirm the communication setting of PCI board.
4. Confirm the address of driver and communication rate setting.
496710 Conveyor Width W3 Error
System setup of Conveyor Width W3 is not completed.
Driver has not completed the parameter setup yet. It is a situation in which a correct setup
has not been received by Communication Error. Check the Communication Mode, wiring,
Power supply of Driver.
49 6711 Conveyor Width W3 Error
Zeroing Error in Conveyor Width W3
LS, discontinuous zeroing movement, was detected. Check out the dirt, error of sensor and
error in Motor body etc.
496212 Conveyor Width W3 Error
Out-of-Control in Conveyor Width W3
Motor Out-of-Control which is over the width of Out-of-Control detecting occurred. Please
execute all zeroing again, and the restart production. Please set motor speed slow if it
happens frequently. Also, in a case of structure motor Error.
496713 Conveyor Width W3 Error
Error in Motor Power voltage of Conveyor Width W3
Motor power voltage dropped. Check out the Power supply line(48V Line)
496714 Conveyor Width W3 Error
STP input in Conveyor Width W3 was detected
STP input is detected. The function to stop motor by Hard signal.
EUKYX
3-96199-4100
3.8 Automatic Adjustment
Error ID Error Name, Description, Cause, and Remedy
496715 Conveyor Width W3 Error
Over-current in Conveyor Width W3
Error in Motor output line. Check out the motor wiring,
496716 Conveyor Width W3 Error
Limit Sensor(+) was detected in Conveyor Width W3.
+LS signal was detected for moving for (+).
Please check the dirt of +LS sensor, disconnection.
49 6717 Conveyor Width W3 Error
Limit Sensor(-) was detected in Conveyor Width W3.
-LS signal was detected for moving for (-).
Please check the dirt of -LS sensor, disconnection.
496718 Conveyor Width W3 Error
Motor Disconnection of Conveyor Width W3 was detected.
Disconnection to motor was detected.(Only stop mode)
Check the motor wiring.
496719 Conveyor Width W3 Error
Control Power Voltage of Conveyor Width W3 has an error
Control power for driver dropped. Check out the Power supply line.(24V Line)
49671a Conveyor Width W3 Error
-----
Reserved Function of driver. Please make inquiries when error is detected.
49671b Conveyor Width W3 Error
-----
Reserved Function of driver. Please make inquiries when error is detected.
49671c Conveyor Width W3 Error
-----
Reserved Function of driver. Please make inquiries when error is detected.
49671d Conveyor Width W3 Error
-----
Reserved Function of driver. Please make inquiries when error is detected.
49671e Conveyor Width W3 Error
-----
Reserved Function of driver. Please make inquiries when error is detected.
49671f Conveyor Width W3 Error
System Error in Conveyor Width W3.
System Error of internal driver. Driver error is supposed if this problem happens frequently.
496720 Conveyor Width W3 Error
Communication Error in Conveyor Width W3.
1. Confirm connection to communication cable.
2. Confirm Power supply(24V).
3. Confirm the communication setting of PCI board.
4. Confirm the address of driver and communication rate setting.
EUKYX
3-97199-4100
3.8 Automatic Adjustment
Error ID Error Name, Description, Cause, and Remedy
496801 Transit communication Error
Communication error occurred in the transfer section.
1. Confirm connection to communication cable.
2. Confirm Power supply(24V).
3. Confirm the communication setting of PCI board.
4. Confirm the address of driver and communication rate setting.
496802 Conveyor Width W1-axis communication Error
Communication error occurred in the W1-axis transfer driver.
1. Confirm connection to communication cable.
2. Confirm Power supply(24V).
3. Confirm the communication setting of PCI board.
4. Confirm the address of driver and communication rate setting.
496803 Conveyor Width W2-axis communication Error
Communication error occurred in the W2-axis transfer driver.
1. Confirm connection to communication cable.
2. Confirm Power supply(24V).
3. Confirm the communication setting of PCI board.
4. Confirm the address of driver and communication rate setting.
496901 Conveyor Width-axis Time-out
Time-out of Zeroing
Check out the dirt, error, disconnection of sensor. If there is no problem with sensor, the
problem could be with motor wire/single error.
496902 Conveyor Width-axis Time-out
Time-out
Check out the dirt, error, disconnection of sensor. If there is no problem with sensor, the
problem could be with motor wire/single error.
496a01 Shuttle Conveyor Error (Input side)
The Cover of Shuttle Conveyor is open.
Please close the cover, and then operate. There is a possibility of Loose Connection or
Defect if the cover is close.
496a02 Shuttle Conveyor Error (Input side)
Emergency Stop of Shuttle Conveyor is detected.
Please cancel Emergency Stop, and then restart to operate again.
496a03 Shuttle Conveyor Error (Input side)
Zeroing of Shuttle Conveyor is not completed within predetermined time.
Check out the dirt, error, disconnection of sensor. If there is no problem with sensor, the
problem could be with motor wire/single error.
496a04 Shuttle Conveyor Error (Input side)
Target Width Matching of Shuttle Conveyor is not completed within predetermined time.
Check out the dirt, error, disconnection of sensor. If there is no problem with sensor, the
problem could be with motor wire/single error.