252301 Issue 2.0 - 第108页

GEM Manual for DEK Printers Equipment Va riables I ssue 2.0 June 9th, 2011 page 108 of 156 NAME ECID DESCRIPTION Type Value Range CameraIdlePosition 8 7 The curr ent selection for the Camera Idle Position optio n (read-o…

100%1 / 156
GEM Manual for DEK Printers Equipment Variables
Issue 2.0 June 9th, 2011 page 107 of 156
NAME ECID DESCRIPTION Type Value Range
PasteDispensePosition 61 The position the paste dispenser uses U1 0=Front
1=Rear
2=Auto
ToolingHardware 62 The currently selected tooling type (read-only) U1
0=Magnetic
2=Vacuum
6=FormFlex
7=GridLok
FiducialReference 63 The current fiducial reference U1
0=Left
1=Right
ProductBarcodeHardw
are
64 The status of the product barcode scanner (read-
only)
U1
0=Not Fitted
1=Fitted
RemoteBarcodeHardw
are
65 The status of the remote barcode scanner (read-
only)
U1
0=Not Fitted
1=Fitted
AdvancedProflow
66 Status of the Advanced ProFlow option U1
0=Disabled
1=Enabled
PressureHardware
67 The currently selected pressure hardware (read-
only)
U1
0=NotFitted
1=Fitted
PasteDispenser 68 The status of the automatic paste dispenser
(read-only)
U1
0=NotFitted
1=Fitted
ScreenSize 69 The current screen type selection (read-only) U1
0=256
1=Fuji
2=249
3=Sanyo
4=Library
RollHeightHardware 70 The current selection of the Paste Roll Height
Monitor (PRHM) hardware (read-only)
U1
0=NotFitted
1=Fitted
RHMOnFailureAction
71 The current setting for failure action on the
PRHM
U1
0=Warn
1=Pause
RollHeightMonitor 72 The current status of the PRHM option U1
0=Disabled
1=Enabled
ConsumableAction 73 The current setting for the action to perform
when a consumable is low
U1
0=Warn
1=Pause
2=Suspend
VacuumHoldTime
74 The time the vacuum is applied to the tolling
before the quality of the vacuum seal is checked
(s)
F8
0.0 – 5.0 sec, 0
TwoDiMovementTunin
g
75 The settling time used in 2D Inspection per site
(ms)
U2
CleanerVacuum
76 The current status of the cleaner vacuum option
(read-only)
U1
0=Standard
1=Vacuum
PasteTrails
77 The current status of the paste trails option U1
0=Disabled
1=Enabled
TransportWaitMode 78 The current setting for the transport wait mode U1
0=Standard
1=Hold At Print
ClampType
80 The current selection for the board clamp type
(read-only)
U1
0=Board Clamps
1=Snuggers
2=Foil Less Clamps
3=Over The Top Snuggers
ToolingMonitoring
81 The rate (in boards) that the Tooling Deviation
Monitoring option is used
U2
0 – 200. 0 = disabled
FiducialMonitoring
83 The current selection for the Fiducial
Monitoring option
U1
0=Smart
1=Normal
FiducialSearch
84 The current selection for the Fiducial Search
option
U1
0=Disabled
1=Custom
RemoteBoardStopHard
ware
85 The current selection for the Remote Board Stop
hardware
(read-only)
U1
0=NotFitted
1=Fitted
BoardStopXOffset
86 The current camera board stop X offset (read-
only)
F8
GEM Manual for DEK Printers Equipment Variables
Issue 2.0 June 9th, 2011 page 108 of 156
NAME ECID DESCRIPTION Type Value Range
CameraIdlePosition 87 The current selection for the Camera Idle
Position option (read-only)
U1
0=Home
1=Behind Rail
UnloadBoardStart
88 The current selection for the Unload Board Start
option
U1
0=Transport
1=Separation
MaintenanceMonitorin
g
95 The current state of the Maintenance Monitoring
option
U1
0=Disabled
1=Enabled
MachineLocation
96 Free format entry to describe the location of the
machine (read-only)
A20
AutoRailWidth
97 The current selection for the Automatic Rail
Width option (read-only)
U1 0=Disabled
1=Enabled
ProductDirectory
98 The path to the local folder where the product
files are stored (read-only)
A260
DataFileLocation 99 The path to the local folder where data and log
files are stored (read-only)
A260
DownlineBoardStop
101 The current selection of the HTC Downline
Board Stop option
U1
0=Never
1=Always
2=Auto
FrontRToLSpeed
104 The speed of the front rail belt when running
from right to left (read-only)
U2
FrontLToRSpeed
105 The speed of the front rail belt when running
from left to right (read-only)
U2
RearRToLSpeed
106 The speed of the rear rail belt when running
from right to left (read-only)
U2
RearLToRSpeed 107 The speed of the rear rail belt when running
from left to right (read-only)
U2
AltFrontRToLSpeed
108 The alternate speed of the front rail belt when
running from right to left (read-only)
U2
AltFrontLToRSpeed
109 The alternate speed of the front rail belt when
running from left to right (read-only)
U2
AltRearRToLSpeed
110 The alternate speed of the rear rail belt when
running from left to right (read-only)
U2
AltRearLToRSpeed
111 The alternate speed of the rear rail belt when
running from right to left (read-only)
U2
<<< End Modification
GEM Manual for DEK Printers Equipment Variables
Issue 2.0 June 9th, 2011 page 109 of 156
7.3 Status Variables
The status variables are defined in the table below:
Name SVID
Limits
Monitor
Description Type Value Range
GemAlarmsEnabled 1001
No
List of alarms that are enabled. List A list of “n” ALID’s.
GemAlarmsSet 1002
No
List of alarms that are set. List A list of “n” ALID’s.
See chapter 6 for ALID’s.
GemAlarmState 1003
No
State of last alarm transition. U1 0 = OFF
1 = ON
clock 1004
No
Host view of equipment time.
(centisecond precision)
A12/A16
Yymmddhhmmss
Yyyymmddhhmmsscc
GemControlState 1005
No
Current GEM Control State. U1 1 = Equipment Off-Line
2 = Attempt On-Line
3 = Host Off-Line
4 = Local
5 = Remote
process_state 1006
No
Current Equipment Process State. U1 0 = Equipment Ready
1 = Equipment Waiting
2 = Equipment Running
3 = Equipment Setup
4 = Equipment Down
5 = Equipment Recovery
6 = Equipment Maintenance
GemEventsEnabled 1007
No
List of collection events enabled. List A list of “n” CEID’s.
See chapter 7.
humidity 1008 Yes Current humidity in print area. F4 0-100 %
model_number 1009
No
Model number. A6 String
previous_command 1010
No
Last command received from operator
or host.
A See appendix A.
GemPreviousControlState
1011
No
Control state prior to last transition. U1 See GemControlState.
last_process_state 1012
No
Process state before last transition. U1 See process_state.
GemPreviousCeid 1013
No
CEID of last collection event to occur.
U4 See chapter 7.
Reserved 1014
No
software_version 1015
No
Software revision 6 char ASCII. A6 See chapter 4. (SOFTREV)
temperature 1016 Yes Current temperature in the print area. F4 0 -100 (Celsius)
current_time 1017
No
Host view of equipment time.
(1 second precision)
A12/A16
Yymmddhhmmss
Yyyymmddhhmmsscc
system_mode 1018
No
The current machine mode. U1 0 = Step
1 = Auto
2 = Single
3 = No Print
PPExecName 1019
No
Name of current process program.
A68
batch_count 1020 Yes
Number of Boards printed.
U4 0-99999
Reserved 1021
No
time_last_print 1022
No
Time of the last print. A12/
A16
Yymmddhhmmss/
Yyyymmddhhmmsscc
spc_data_mode 1023
No
Reporting mode of the SPC. U1 0 = Serial
1 = Disk
2 = Invalid
3 = None