7OM-1625-004_w - 第60页
7OM-1603 Chapter 1 : 3. Name of Each Section and Handling 1-19 3.4.3 Replacement of Magazine • Attachment Procedure of Magazine Procedure (1) Conrm that the LED of the [READY] switch is "OFF" and then open the…
7OM-1603
1-18
Chapter 1 : 3. Name of Each Section and Handling
3.4.1 Attachment Procedure of Pallets
NOTICE
Be sure to insert a pallet horizontally into the
magazine.
Otherwise, the traverse cannot pull out the pallet, causing
the components in the tray of the pallet to disperse or the
machine to be damaged.
Procedure
(1) Open the magazine door.
Notice
When the feeder is operated with the magazine door being
deformed, it may break down.
(2) Observe the right and left stage Nos. and insert the tray-loaded pallet into the
magazine.
Notice
•
When a pallet is to be inserted into the magazine, make sure that
the pallet is inserted correctly with its top side facing upward.
When the pallet is inserted upside down, a breakdown will result
because the error cannot be detected.
•
The use of the pallet for GXH-1/3 is not available.
When the pallet for GXH-1/3 is installed onto the magazine, the
magazine door can not be closed completely.
(3) Close the magazine door.
Notice
Be sure to close the magazine door slowly and securely. Otherwise,
some components may pop out of the tray.
If the magazine door is not closed securely, the magazine may open
while the feeder is running and the feeder may break down.
3.4.2 Detachment of Pallets
Procedure
(1) Open the magazine door.
(2) Pull out the desired pallet from the magazine.
1007-003
7OM-1603
Chapter 1 : 3. Name of Each Section and Handling
1-19
3.4.3 Replacement of Magazine
•
Attachment Procedure of Magazine
Procedure
(1) Conrm that the LED of the [READY] switch is "OFF" and then open the
door.
Note
When the LED illuminates in green, the door cannot be opened.
(2) While pulling out the magazine stopper knob forward, turn it clockwise by
approximately 90°.
Knob
While pulling out the knob forward, turn it clockwise by approximately 90° .
2
1
Magazine Base F7A7
1007-002
7OM-1603
1-20
Chapter 1 : 3. Name of Each Section and Handling
(3) Hold the handle in the magazine base and slowly pull it out until it stops.
Handle
Magazine Base (Drawer) F7A8
(4) Hold the magazine handle and put the magazine slowly on the magazine
loading section. Then, press the magazine against the stopper on the rear side
to conrm that the magazine is completely housed in the loading space and it
does not inclined.
(5) Hold the handle of the magazine base and slowly push the base toward the
rear side until it touches the rear side.
(6) While pulling the magazine stopper knob forward, turn it counterclockwise
by 90°. Then, return the magazine stopper back in place.
(When the magazine is located at its home position, it is locked by the
magazine stopper.)
Notice
The use of the magazine for GXH-1/3 is not available.
Even when the magazine for GXH-1/3 is setup, it is not recognized
as a magazine.
(7) Close the magazine exchange door and press the ready switch.
(The magazine exchange door is locked electromagnetically and the LED of
the ready switch illuminates.)
Note
This machine keeps the last component ID matrix position in memory even
after the current program (model) is changed to another one.
Before reloading the tray in the middle of process with some components
after the current program (model) is changed to another one, it is required
to change the matrix because some components are left behind (not picked
up).
1003-002