00194547-03 - 第69页

Installation Manual Station Software Version 601.02 SP1 Edition 10/2005 69 of 82 4.7.4 Setup page "Integrated Peripherals Feature" OnChip IDE Device Menu item Note Selection options Settings Note On-Chip Primar…

100%1 / 165
Installation Manual Station Software Version 601.02 SP1 Edition 10/2005
68 of 82
Menu item Note Selection options Settings Note
Panel Scaling
This item is only active if the ’On-Chip VGA’ item is
enabled.
This item is for future video/BIOS configurations
and currently has no effect.
Adjusts graphics output to the resolution of the
connected display. If "Off" is selected and a
1024x768 pixel display is connected, for example,
the BIOS output is centered on the display.
Auto
On
Off
Auto
Panel Number
This item is only active if the ’On-Chip VGA’ item is
enabled.
This item is for future video/BIOS configurations
and currently has no effect.
If this is used, a display configuration stored in the
Video BIOS can be selected here. The selected
configuration (resolution) is then used. This setup
item is important when using displays without EIDE
(Extended Display Information Data).
1; 2; 3; 4; 5; 6; 7; 8; 9;
10; 11; 12; 13; 14; 15; 16
1
Installation Manual Station Software Version 601.02 SP1 Edition 10/2005
69 of 82
4.7.4 Setup page "Integrated Peripherals Feature"
OnChip IDE Device
Menu item Note Selection options Settings Note
On-Chip Primary
PCI IDE
Enabling this field enables the primary IDE channel
on which devices can be run.
Enabled
Disabled
Enabled
IDE Primary
Master PIO
Sets the PIO mode for the master on the primary
IDE channel. Higher values mean faster access.
Auto sets the maximum permissible value for the
disk.
Auto; Mode 0;
Mode 1; Mode 2;
Mode 3; Mode 4
Auto
IDE Primary
Slave PIO
Sets the PIO mode for the slave on the primary IDE
channel. Higher values mean faster access. Auto
sets the maximum permissible value for the disk.
Auto; Mode 0;
Mode 1; Mode 2;
Mode 3; Mode 4
Auto
IDE Primary
Master UDMA
If Auto is set, UDMA mode is enabled for the master
on the primary IDE channel if it is supported by the
disk.
Auto;
Disabled
Auto
IDE Primary
Slave UDMA
If Auto is set, UDMA mode is enabled for the slave
on the primary IDE channel if it is supported by the
disk.
Auto;
Disabled
Auto
UDMA66/100
allowed
In the specification for UDMA66 and UDMA100, an
80-pin cable is required. You can use this option to
also run drives which support these modes with a
short 40-pin cable on the primary IDE channel.
No;
Yes
Yes
On-Chip
Secondary PCI
IDE
Enabling this field enables the secondary IDE
channel on which devices can be run.
Enabled
Disabled
Disabled
IDE Secondary
Master PIO
Sets the PIO mode for the master on the secondary
IDE channel. Higher values mean faster access.
Auto sets the maximum permissible value for the
disk.
Auto; Mode 0;
Mode 1; Mode 2;
Mode 3; Mode 4
Auto
Installation Manual Station Software Version 601.02 SP1 Edition 10/2005
70 of 82
Menu item Note Selection options Settings Note
IDE Secondary
Slave PIO
Sets the PIO mode for the slave on the secondary
IDE channel. Higher values mean faster access.
Auto sets the maximum permissible value for the
disk.
Auto; Mode 0;
Mode 1; Mode 2;
Mode 3; Mode 4
Auto
IDE Secondary
Master UDMA
If Auto is set, UDMA mode is enabled for the master
on the secondary IDE channel if it is supported by
the disk.
Auto;
Disabled
Auto
IDE Secondary
Slave UDMA
If Auto is set, UDMA mode is enabled for the slave
on the secondary IDE channel if it is supported by
the disk.
Auto;
Disabled
Auto
UDMA66/100
allowed
In the specification for UDMA66 and UDMA100, an
80-pin cable is required. You can use this option to
also run drives which support these modes with a
short 40-pin cable on the secondary IDE channel.
No;
Yes
No
IDE HDD Block
Mode
This enables the transfer of entire blocks from the
hard disk to the memory instead of individual
sectors.
Enabled
Disabled
Enabled
Delay for HDD
(Secs)
Time the CPU waits before accessing connected
ATA devices (e.g. hard disks, CD ROMs).
0; 1; 2; 3; 4; 5; 6; 7; 8; 9;
10; 11; 12; 13; 14; 15
0 As of BIOS
V1.05c
Onboard Device
Menu item Note Selection options Settings Note
USB Controller
If this setting is disabled, the USB controller is disabled and
no USB devices can be run on the module.
Enabled
Disabled
Enabled
USB 2.0
Controller
If this setting is disabled, the USB 2.0 controller is disabled
and no USB 2.0 devices can be run in USB 2.0 mode on
the module. Such devices are then run as USB 1.1
devices.
Enabled
Disabled
Enabled