00191413-01 - 第27页
User Manual Line Computer UNIX 1 Hardware / Software Install ation Software Version 501.xx 01/99 Issue 1.2 Software Install ation 1 - 9 After a wh ile, the fo llowi ng messages are di splayed on the sc reen: This is the …
1 Hardware / Software Installation User Manual Line Computer UNIX
1.2 Software Installation Software Version 501.xx 01/99 Issue
1 - 8
1.2.2 Definition of Terms
- Initial Installation
Prior to the start of the installation of the LC software, the computer must be in a neutral state, i.e. the
SCO OpenServer 5.0.4 operating system has been installed, but no further data exist on the hard disk
yet. This basic state exists when the unit is delivered.
When the LC software is then installed with the aid of the installation program, also the sample master
data are installed on the hard disk.
- Update
When the only difference between the new LC software and the one already installed is their revision
level, (e.g. LRU.404.03 => LRU.404.04) this is referred to as an update. Any errors that may have
occurred in the predecessor version have been eliminated in the update version, and the software has
been optimized. In the case of an update, the master data are retained.
- Upgrade
When the new software differs from the one already installed in that their version designations are
different, (e.g. LRU.404.06 => LRU.501.01) this is referred to as an upgrade. An upgrade version con-
tains new functions. In the case of an upgrade, the master data are retained and, if required, automati-
cally converted into the new data format.
1.2.3 Installation of LC Software
● Insert the Boot Diskette (1).
ATTENTION !
Be sure to use only the boot diskette appropriate for your specific computer type (see section 1.2.1).
● Turn on the UPS.
● Press RETURN when the line "Boot:" is displayed on the screen.
The line computer is now booted from the diskette.
After approx. 1 minute the following message is displayed on the screen:
Insert installdisk and press <Return> to continue
or remove the bootdisk and press <Return> to quit (ignore Warnings)
NOTE
When this message is displayed, the installation procedure can still be stopped by removing the boot
diskette and subsequently pressing the RETURN key. The error messages subsequently displayed
can be ignored. The state of the LC software is unchanged.
● Remove Boot Diskette, insert Installation Diskette (2) and press RETURN.
User Manual Line Computer UNIX 1 Hardware / Software Installation
Software Version 501.xx 01/99 Issue 1.2 Software Installation
1 - 9
After a while, the following messages are displayed on the screen:
This is the last point to abort the LRU-installation
without changing any data.
If you have installed OEM-software, you have to reinstall it
after the LRU-installation
Do you want to continue the LRU-installation [y/n]
Abort Installation:
● Enter
n
for the installation to be aborted and then press RETURN.
The following steps are displayed for terminating the installation procedure and rebooting the
line computer:
Next steps
1.) Remove the floppy after the Safe to Power Off message
2.) reboot your system
3.) login as plr
** Safe to Power Off **
- or -
** Press Any Key to Reboot **
The computer can now be rebooted. The LC software’s state is still unchanged.
Continue Installation:
● Enter
y
to continue the installation process and then press RETURN.
The computer system is shut down. The following steps are displayed for continuing the
installation procedure:
PL EA pre-install finished
Next steps
1.) Remove the floppy after the Safe to Power Off message
2.) insert the CD
3.) reboot your system
4.) login as plr
** Safe to Power Off **
- or -
** Press Any Key to Reboot **
1 Hardware / Software Installation User Manual Line Computer UNIX
1.2 Software Installation Software Version 501.xx 01/99 Issue
1 - 10
● Remove Installation Diskette and insert the CD-ROM.
● Press any key on the keyboard.
The system is rebooted. When the booting procedure has been completed, the following lines
are displayed:
login:
● Enter
plr
after "login:" and press RETURN.
Password:
● Enter
plr
after "Password" and press RETURN.
The CD-ROM is now read in. This takes approx. 10 minutes.
While the data are being read in, information about the ongoing activities is displayed.
If no data are available in the line computer, the following query appears:
There is no user data (SDH) on the line computer.
Do you want to install default libraries (GF-/BE-/RI-Bibliothek..) [y/n]
● Enter
y
and confirm your entry by pressing RETURN. The default libraries are now installed.
NOTE
If
n
was entered, only the ST-library is installed.
The following query appears:
Converting GF-Bibliothek (7xx/8xx-nozzle)
You can update the GF-Bibliothek later too.
Do you want to update 7xx/8xx-nozzles
and sensor specific information (10/12/13/14/17.SST) now [y/n]
● Enter
y
and confirm your entry by pressing RETURN.
The 7xx/8xx type nozzles and the sensor types 10, 12, 13, 14, 17 are being entered in the GF-
files. Previously entered 7xx-nozzles are retained.
In the standard range (GF-nos. 1 through 1499) the allocation of the nozzles is carried out via a Table.
The allocations of customer-specific package forms are calculated.
In the Import/Expor directory a "GFupgrade403.log" file is created containing a list of all alloca-
tions. The content of the file can be displayed and printed out by means of the file display option
(see chapt. 4, section 4.5).
Any incorrectly assigned nozzles can be changed subsequently by means of the Package Form
Editor.