00195941-03-UM SiplaceCA-EN - 第282页
4 Setting Up and Commissioning User Manual SIPLACE CA 4.5 Setting Up the Placement Machine Edition 08/2011 EN 282 4 Fig. 4.5 - 9 Fitting the conveyor cover and the second half of t he extension kit (1) Half of the extens…
User Manual SIPLACE CA 4 Setting Up and Commissioning
Edition 08/2011 EN 4.5 Setting Up the Placement Machine
281
CAUTION 4
Do not unscrew the three bottom screws straight away. Simply loosen them so that the side
plate does not fall off.
Detach the ground cable from the side plate.
Remove both doors (item 2 in fig. 4.5 - 8) from the extension kit (item 1).
Note: 4
To avoid damage, we recommend that a second person helps to assemble the extension kit.
Place the axis unit (item 8 in fig. 4.5 - 8) down at the side of the placement machine, so that
you have enough room to fit the extension kit (item 1 in fig. 4.5 - 8
).
Make sure that the connecting cables to the axis unit are not too tight.
Lift one half of the extension kit (item 1 in fig. 4.5 - 8) against the machine frame and position
it so that the assembly bracket lies on the assembly bar (item 7 in fig. 4.5 - 8
).
CAUTION 4
Make sure that this half of the extension kit does not collide with the hexagonal shaft of the
PCB conveyor and thus bend the shaft.
Fasten this half of the extension kit with 2 fillister head screws M6x16 and the corresponding
discs (item 3 in fig. 4.5 - 8
).
Before assembling the second half of the extension kit, fit the conveyor covers (item 5 in fig.
4.5 - 8
). The procedure is as follows:
4 Setting Up and Commissioning User Manual SIPLACE CA
4.5 Setting Up the Placement Machine Edition 08/2011 EN
282
4
Fig. 4.5 - 9 Fitting the conveyor cover and the second half of the extension kit
(1) Half of the extension kit already fitted
(2) Second half of the extension kit to be fitted
(3) Transport cover
(4) Insert 3 white plastic washers on both sides
(5) Mandrel of the conveyor cover
(6) Hole
(7) Protective cover switch
Insert 3 white plastic discs (item 4 in fig. 4.5 - 9) on each of the two mandrels (item 5 in fig.
4.5 - 9
).
Insert the mandrel (item 5 in fig. 4.5 - 9) into the drilling (item 6 in fig. 4.5 - 9).
Lift the second half of the extension kit (item 2 in fig. 4.5 - 9) up to the machine frame.
User Manual SIPLACE CA 4 Setting Up and Commissioning
Edition 08/2011 EN 4.5 Setting Up the Placement Machine
283
4
CAUTION 4
Make sure that this half of the extension kit does not collide with the hexagonal shaft of the
PCB conveyor and thus bend the shaft.
Insert the mandrel (item 5 in fig. 4.5 - 9) for the conveyor cover into the drilling (item 6 in fig.
4.5 - 9
) on the second half of the extension kit.
Position the second half of the extension kit so that the assembly bracket lies on the assembly
bar (item 7 in fig. 4.5 - 8
).
Fasten this second half of the placement machine with 2 fillister head screws M6x16 and the
corresponding disc (item 3 in fig. 4.5 - 8
).
4.5.7.3 Fastening the Hexagonal Shaft Guidance
When using a single conveyor, fasten one guidance for the hexagonal shaft (item 8 in fig. 4.5
- 7) onto the extension kit, with two fillister head screws M6x16 and discs.
When using a dual conveyor, fasten two guidances for the hexagonal shaft (item 8 in fig. 4.5
- 7) onto the extension kit, with two fillister head screws M6x16 and discs.
4.5.7.4 Establishing Cable Connections - Extension Kit on the PCB Output Side
4
4
Left-hand side of the extension kit
(viewed in the direction of travel)
Connector/cable To connector/cable
EMERGENCY STOP button
Start/Stop button
X63/03020687 X63/03002526
Protective cover switch, location 3
X53/03020409 X53/03002528
Button for the component trolley docking unit,
location 3
X232/03021056 X232/03021053
Right-hand side of the extension kit
(viewed in the direction of travel)
Connector/cable To connector/cable
Start/Stop button
Switch, PCB conveyor cover
X62/03020410 X62/03002525
Protective cover switch, location 2
X52/03006476 X52/03002527
Button for the component trolley docking unit,
location 2
X222/03021056 X222/03021052