00195941-03-UM SiplaceCA-EN - 第355页

User Manual SIPLACE CA 5 Tasks on the Machine Edition 08/2011 EN 5.5 Configuring Fee ders 355  Shorten the component t ape with the now ex posed component pockets by aro und 3 cm.  Remove the component s from the open …

5 Tasks on the Machine User Manual SIPLACE CA

5.5 Configuring Feeders Edition 08/2011 EN

354

 Check the "back" centering pin (item 3) of the feeder module as you do so. This must slide

easily into the recess (item 5) in the centering bar, otherwise the feeder module is not seated

vertically on the component table or it was not placed on the guide profile (item 8) correctly.

 The locking latch (item 7) engages with the locking roller of the feeder (item 1 in fig. 6.1 - 1).

If you have forgotten to engage the removal handle (item 1 in fig. 5.5 - 2

, page 352), the status

display on the feeder operating panel will shine red after a few seconds. The LCD display will

show the error message "Handle --->>" (see fig. 5.7 - 1

, page 360). 5

 Engage the removal handle (item 1 in fig. 5.5 - 2). The feeder module's status display

now lights up green and the feeder module is on standby. The track number and con-

veyor increment can be read on the LCD display once more.

5.5.4 Placing Component Tape on the X Feeder Module

5.5.4.1 Checking the X Tape Feeder

 When you insert the tape into the feeder, check whether there are any components in the

pickup window area (item 2 in fig. 5.5 - 5

 Remove any components that you find since they could cause a fault.

5.5.4.2 Preparing the Component Tape for Insertion

 Check that there is a straight cut edge at the start of the component tape.

 If the transport holes are torn or bent, cut off this part of the tape.

 Also make sure that there are no streaks of adhesive on the cover foil.

 Pull around 30 cm cover foil away from the component tape if this does not expose any

components.

NOTE 5

Use the SMD tape threading aid if there is not enough cover foil available, to prevent compo-

nents being lost:

for the 8 mm - tape: [00355265-xx]

for the 12 mm - tape: [00356342-xx]

User Manual SIPLACE CA 5 Tasks on the Machine

Edition 08/2011 EN 5.5 Configuring Feeders

355

 Shorten the component tape with the now exposed component pockets by around 3 cm.

 Remove the components from the open tape pockets.

 Wrap the cover foil around the front edge of the tape along the bottom of the tape.

5.5.4.3 Inserting the Tape into the X Feeder

Fig. 5.5 - 4 Inserting the component tape

(1) Entry of the tape guide channel

(2) Operating panel

(3) Outlet of the tape guide channel

(4) Pickup window

(5) Lever for raising the pickup window

 Hold the component tape so that the transport holes are on the left-hand side viewed in the

direction of travel.

 Insert the tape into the inlet opening (item 1 in fig. 5.5 - 4) of the tape guide channel, until the

tape protrudes from the tape outlet (item 3 in fig. 5.5 - 4

 Pull the component tape up and out, and fold the cover foil back against the top of the tape.

5 Tasks on the Machine User Manual SIPLACE CA

5.5 Configuring Feeders Edition 08/2011 EN

356

 Guide the start of the tape under the pickup window (item 2 in fig. 5.5 - 5) and on, until the

tape touches the sprocket wheel.

Fig. 5.5 - 5 Pickup window on the tape feeder module

(1) Tape support, removable

(2) Pickup window

(3) Pull-off edge for the cover foil

(4) pickup area for the components

(5) Lever for raising and latching the pickup window

 Press the FORWARDS button on the operator panel (item 1 in fig. 5.5 - 6) until the fold in the

cover foil is in the component pickup area (item 4 in fig. 5.5 - 5