88242361-04-01 Vol 1 DEK TQ TECHNICAL REFERENCE (1) - 第87页
6 MACHINE CONTROL 6.4 EXTENDED POWER MODULE (EPM) TECHNICAL REFERENCE MANUAL DEK TQ 04/2021 87 EPM 3 Lower Connector Fuse Description J2-1 F2-1 (5A) Camera Y Linear Drive J2-2 F2-2 (2A) Under Stencil Cleaner Y Linear Dri…
6 MACHINE CONTROL
6.4 EXTENDED POWER MODULE (EPM)
86 TECHNICAL REFERENCE MANUAL DEK TQ 04/2021
6.4.2 Servo Drive Card
Servo drive cards are used to drive the following servo motors:
●
Camera Y and X Drive
●
Tooling Table Lift
●
Conveyor Lift
●
Print Carriage Drive
●
Conveyor Width (APC Conveyors)
●
Under Stencil Cleaner
6.4.2.1 Connectors
J*-1
J*-2
J*-3
J*-4
J*-5
F*-3
F*-1
F*-4
F*-2
Servo Drive Card Connectors
NOTE
J* is either J1 if the drive card is in the upper position (top) or J2 if in the lower position (bottom) of
the EPM.
F* is either F1 if the drive card is in the upper position (top) or F2 if in the lower position (bottom) of
the EPM.
EPM 3 Upper
Connector Fuse Description
J1-1 F1-1 (2.5A) Tooling Table Lift
J1-2 F1-2 (2.5A) Conveyor Lift
J1-3 F1-3 (2A) Print Carriage Drive
J1-4 F1-4 (2A) Camera X Linear Drive
J1-5 Power Input
6 MACHINE CONTROL
6.4 EXTENDED POWER MODULE (EPM)
TECHNICAL REFERENCE MANUAL DEK TQ 04/2021 87
EPM 3 Lower
Connector Fuse Description
J2-1 F2-1 (5A) Camera Y Linear Drive
J2-2 F2-2 (2A) Under Stencil Cleaner Y Linear Drive
J2-3 F2-3 (2A) Conveyor Width Left Linear Drive (APC Conveyors)
J2-4 F2-4 (2A) Conveyor Width Right Linear Drive (APC Conveyors)
J2-5 Power Input
J*-1, J*-2, J*-3 and J*-4
1
4
Pin No Signal Pin No Signal
1 MTR Phase R 3 MTR Phase S
2 Earth 4 MTR Phase T
J*-5
1
6
Pin No Signal Pin No Signal
1 48V SW 4 48V SW
2 0V 5 0V
3 Not Used 6 24V US
6.4.2.2 LEDs
LED 1
LED 2
24V
Logic
LED 3
LED 4
F*-3
F*-1
F*-4
F*-2
Each output has its own fuse and indicator LED. If a fuse is blown, the LED is dimmed.
6 MACHINE CONTROL
6.5 ENCODER SERIAL INPUT OR OUTPUT (ESIO) MODULES
88 TECHNICAL REFERENCE MANUAL DEK TQ 04/2021
6.5 ENCODER SERIAL INPUT OR OUTPUT (ESIO) MODULES
The ESIO modules connect to the CPM using serial cable and are located close to the mechanical
module that they relate to. There are three different types of ESIO modules located around the
machine:
ESIO 12 ESIO 15
Digital Input and Output Ports 24 16
Encoder Ports 4 2
ADC and DAC Ports 0 1
The following table indicates what type of ESIO is used:
Item Type
ESIO-1 ESIO 12
ESIO-2 ESIO 15
ESIO-3 ESIO 12
ESIO-4 ESIO 12
ESIO-5 ESIO 15
ESIO-6 ESIO 15