SIPLACE X-Series (SIPLACE X-Series S, from SC 708.1) Edition 05/2015 EN User manual - 第202页
3 Technical data and assemblies User manual SIPLACE X-Series 3.9 X feeder modules for SIPLACE X-Series From software version 708.1 Version 05/2015 202 3.9.7.1 T echnical dat a 3 3.9.7.2 Number of waffle p ack trays per l…
User manual SIPLACE X-Series 3 Technical data and assemblies
From software version 708.1 Version 05/2015 3.9 X feeder modules for SIPLACE X-Series
201
3.9.7 Tray holder for the component trolley of the SIPLACE X-Series
Item no. 00141285-xxTray holder for X-Series
3
Fig. 3.9 - 21 Tray holder
(1) Tray holder for SIPLACE X-Series
(2) Bracket for 2nd JEDEC waffle pack tray
(3) Waffle pack tray carrier
(4) Stop bar for the JEDEC waffle pack tray
(5) Locating pin - zero point of JEDEC waffle pack tray
3
Individually placed JEDEC waffle pack trays or waffle pack magazines can be fixed to the waffle
pack tray carrier with magnets. If two JEDEC waffle pack trays are placed, these will need to be
fixed into place with locking bars or mounting rails, as used for the MTC waffle pack tray carriers.
Parts: Item no.:
Magnet 00316593-xx
Locking bar/mounting rail for JEDEC magazines 00372615-xx
3 Technical data and assemblies User manual SIPLACE X-Series
3.9 X feeder modules for SIPLACE X-Series From software version 708.1 Version 05/2015
202
3.9.7.1 Technical data
3
3.9.7.2 Number of waffle pack trays per location and machine
3.9.7.3 Inserting tray holder on the X-Series component trolley
Place the two front slider guides (item 1 in fig. 3.9 - 22, page 203) for the holder onto the in-
sertion aid (item 6 in fig. 3.9 - 22, page 203 ).
Push the holder along the guide profiles (item 7 in fig. 3.9 - 22, page 203), towards the front.
The holder slides with the front (item 1) and back slide guides (item 2 in fig. 3.9 - 22, page
203) on the guide profiles.
Continue pushing the holder, until the two centering pins "front" (item 4 in fig. 3.9 - 22, page
203) disappear into the centering holes (item 10 in fig. 3.9 - 22, page 203).
Check the two "back" centering pins (item 3 in fig. 3.9 - 22, page 203) for the holder. They
should slide easily into the recesses (item 8 in fig. 3.9 - 22, page 203) of the centering rail.
At the end stop of the holder, the locking latches (item 9 in fig. 3.9 - 22, page 203) engage
with the locking rollers (item 5) of the holder.
The waffle pack tray holder can be locked and released via the user interface. You can therefore
easily change the holder without interruption to machine operation.
Dimensions L x W x H 429 mm x 376 mm x 200 mm
Location occupied on the changeover table 32 locations
*a
*)a X feeder modules can be placed on the remaining 8 locations. When using locking bars/mounting rails, the
locations available are reduced to 6, due to the fixation lever which protrudes at the side.
Positioning options on X-Series placement ma-
chines
Locations 2 and/or 4
Placement head range TwinStar, CPP
*b
*)b Only permitted in high assembly position (CPP_H).
PLEASE NOTE
Further information
The maximum component height for the waffle pack tray holder depends on the maxi-
mum component height for the placement head used. When using waffle pack trays,
bear in mind that the components may not higher than the pickup height of a standard
feeder.
Placement machine Location 2 Location 4
X4 S 1 1
X3 S 2 1
X2 S 2 2
User manual SIPLACE X-Series 3 Technical data and assemblies
From software version 708.1 Version 05/2015 3.9 X feeder modules for SIPLACE X-Series
203
3
3
Fig. 3.9 - 22 Using waffle pack tray holder on component trolley for X-Series
WARNING
Occupation of locations!
Always follow the safety instructions about occupying locations, in section 2.6.6
, page 93.
(1) Front slider guide (6) Insertion aid
(2) Back slider guide (7) Sliding rail (omega profile)
(3) "Back" centering pin (8) Recesses in the centering bar for holding the
"back" centering pin
(4) "Front" centering pin (9) Locking latches
(5) Locking roller (10) Centering holes on the changeover table for
holding the "front" centering pin