SIPLACE X-Series (SIPLACE X-Series S, from SC 708.1) Edition 05/2015 EN User manual - 第295页

User manual SIPLACE X-Series 5 Working with the machine From software version 708.1 Version 05/2015 5.9 Carrying out a sight check 295 5  Check the multicolor status displa y (item 3 in fig. 5.9 - 1 , pa ge 294 ). – If …

100%1 / 430
5 Working with the machine User manual SIPLACE X-Series
5.9 Carrying out a sight check From software version 708.1 Version 05/2015
294
5.9 Carrying out a sight check
5.9.1 Checking the X feeder modules
5
Fig. 5.9 - 1 Checking the X feeder modules
(1) Flap
(2) Blade
(3) Status display
(4) LCD display
5
Check to see whether the tape foil removal container for the X tape feeder module is full.
Open the flap (item 1). Pull out the cover foil and cut it with scissors or on the integral blade
(item 2) on 8 and 12 mm X tape feeder modules.
User manual SIPLACE X-Series 5 Working with the machine
From software version 708.1 Version 05/2015 5.9 Carrying out a sight check
295
5
Check the multicolor status display (item 3 in fig. 5.9 - 1, page 294).
– If it lights up green, the feeder module is on standby.
– If it lights up orange, it is signaling a warning. The text of the warning
appears on the LCD display (item 4 in fig. 5.9 - 1
, page 294). The LEDs shine accordingly
for Smart Feeders.
– If the status display lights up red, a malfunction has occurred. The error message
appears on the LCD display (item 3 in fig. 5.9 - 1
, page 294). The LEDs shine accordingly
for Smart Feeders.
A list of the LCD and status displays on the operator panel is given in section 5.11
, page
310
. 5
A list of the LED and status displays on the Smart Feeder operator panel is given in sec-
tion 5.11.2
, page 311. 5
If the status display is off, the cause may be as follows: 5
– The feeder module is not in the current setup.
– The feeder module is defective.
– The feeder module has been disabled (due to a drop in pressure, for example)
5.9.2 Splicing the tapes in good time
5
CAUTION
Problems with cover foil withdrawal!
If the cover foil tears, this could lead to problems with the cover foil withdrawal.
There is an integral blade (item 2) for easily cutting the on the 8 and 12 mm X tape feeder
modules.
PLEASE NOTE
Late splicing of tapes
Late splicing of tapes can lead to prolonged down times.
Splice the tapes early enough so that the feeder modules do not run out of compo-
nents.
PLEASE NOTE
Early splicing of tapes
Early splicing of tapes can have the following consequence: when the old tape is rolled
up onto the new reel, the new reel could become too full and the tape will slide off it and
get caught up. This will again result in pick-up errors and prolonged down times.
Splice the tapes at the right time so that the old and new tapes do not get caught.
5 Working with the machine User manual SIPLACE X-Series
5.9 Carrying out a sight check From software version 708.1 Version 05/2015
296
5.9.3 Checking the PCB supports
Check the position of the magnetic PCB supports on the lifting table:
– Make sure that the PCB supports do not collide with components on the underside of the
PCBs.
– In addition, make sure that the PCB supports do not collide with the PCB conveyor pan-
els.
– Only use PCB supports as described in section 6.14
, page 399.
5.9.4 Mount of additional tape reel
5
Fig. 5.9 - 2 Mount of additional tape reel
(1) Mount of additional tape reel, item no. 00141217-xx
(2) Mounting device for the support
5
Max. 60 mm