SM_SXDX12_intern_03-2017_en - 第24页

Service Work Y-guide carriage / Y-loose bearing Replace 24 Service Manual (Internal) SIPLACE SX1/SX2/DX1/DX2 2.6 Y-guide carriage / Y -loose bearing Replace Required spare parts 2 x 03059084Sxx Guide Carr iage Y MRC 25-G…

Service Work

Exchange / Demounting of Y-Magnets

Service Manual (Internal) SIPLACE SX1/SX2/DX1/DX2 23

▪ Keep holding the magnets so long until this is fixed with the first screw.

▪ Turn the remaining ones bolts. Press the magnet against the spacer and tighten the bolts with a

torque wrench with 9 Nm.

▪ Install the remaining magnets successively by preserving this way of working.

Finally, remove the safety covers by lifting them slightly, pull on the Teflon plate and lift them whole.

Thereby you avoid scratching the magnets.

Service Work

Y-guide carriage / Y-loose bearing Replace

24 Service Manual (Internal) SIPLACE SX1/SX2/DX1/DX2

2.6 Y-guide carriage / Y-loose bearing Replace

Required spare parts

2 x 03059084Sxx Guide Carriage Y MRC 25-G2-V1

Includes:

1 x 03059084-xx Guide Carriage Y MRC 25-G2-V1

1 x 00316894-xx DIN 125-A 3.2-140HV-A2

1 x 03069101-xx ISO 4762 - M 4 x 16-8.8, zinc, DSP

1 x 03074058-xx Adapter with groove

4 x 03046828-xx DIN912-M6 x 12-8.8, zinc. DSP

1 x 03076849Sxx Running Block LR205-2RSR

Includes:

2 x 03076849-xx Running Block LR205-2RSR

2 x 03042601-xx Roller axle D25

2 x 03042601-xx ISO 4762 - M 10 x 35-A2-70

2 x 03076895-xx Slice Distance- 34x20.5x3.0

Consumables required:

02101037-xx LOCTITE 241 SCHRAUBENSICH. Medium strenght

00318197-xx Thread red lock

Tools required

1 x 60519813-xx Gantry lift, SX1/2 CoD

1 x 60519814-xx gantry carrier, SX1/2 CoD

4x 03082592-xx Cardboard lid for 03064172-01

2x 03097870-xx Plastic wedge, 65 x 180mm → wedge, plastic, 65 x 180mm

1 x 03097897-xx copper hammer, 750 g

4 x 03097977-xx safety cover Y magnets SIPL.SX1 - → safety cover Y-magnet SIPL.SX1_2

1 x 00375988-xx label: Warning of a magnetic field

1 x 00386029-xx label: Warning hand injuries

1 x 00386030-xx label warning for strong magnets

1 x 00195600-xx TI Safety note maglev, D + E

2 x 03067676-xx Transport Lock X-Rail, cpl

1 x 00376625-xx Torque wrench with reversible ratchet

1 x 03065304-xx spacer for Y magnets

1 x 03071361-xx read head MS20.xxM / test device PG-U

1 x 03090774-xx feeler gauge 0,75mm plastic

Standard tool kit from service suitcase

1 x 00376492-xx set-hexagon socket cranked screw key

1 x 00096290-xx open end wrench set

1 x 00376516-xx Wrench set 1/4 inch

1 x 00094020-xx feeler gauges

1 x 00376515-xx flashlight

Service Work

Prepare the guide carriage Y-guide carriage / Y-loose bearing Replace

Service Manual (Internal) SIPLACE SX1/SX2/DX1/DX2 25

2.6.1 Prepare the guide carriage

▪ Place the "adapter with groove" 03074058-xx on the

guide carriage Y MRC 25-G2-V1 03059084-xx and fix

it with 4 DIN912-M6 x 12-8.8, verz.DSP bolts

[03046828-xx] The screws are by hand tightened.

▪ Press the adapter as shown in the image away from

the ground surface.

▪ The ground surface is later used as installation edge

at the gantry

▪ Tighten the screws (10Nm) and mark the position

with the "thread red lock paint" .

▪ 1. ground surface

▪ Insert the new guide carriages into the guide

rail. (for example on the gantry carrier)

▪ Ask the stripping plates so that they do not r

gainst the guide rail. An air gap must be on

both sides between the rail and wipers .

▪

▪ Insert this again onto the plastic rail.