00197551-01_MM_CPP-CP-Twin_Kunde_en - 第50页

Maintenance Tasks for C&P20/A/M/P Head Performing Maintenance Tasks 4.6.5 Oiling the DP Driver Bearing 50 Maintenance Manual SIPLACE Placement Heads CPP, C&P20, Twin 4.6.5 4 . 6 . 5 O ilin g t h e D P D r iv e r …

100%1 / 92
Maintenance Tasks for C&P20/A/M/P Head
4.6.4 Oiling the Z Axis Linear Guidance Performing Maintenance Tasks
Maintenance Manual SIPLACE Placement Heads CPP, C&P20, Twin 49
4.6.4
4.6.4 Oiling the Z Axis Linear Guidance
Oiling the Z Axis Linear Guidance
► For this maintenance task, use the blue combitip with Thermoplex ALN 1001/00.
► Set the multipette to 4 µl.
► Remove the black rubber hose between the Z axis and the driver.
► Hold the Z axis by the rotor, in its uppermost position.
► Clean the linear guide with a lint-free cloth or a clean-
ing stick.
► Apply 4 µl of lubricant to the outer guideway of the
rail.
Make sure that the application nozzle is positioned
near to the guidance trolley.
► Move the Z axis into its bottom position.
► Apply 4 µl of lubricant to the inner and outer guideway
of the rail and move the Z axis approx. five times
manually in and out.
► Apply another 4 µl of lubricant to the inner and outer
guideway of the rail and move the Z axis again ap-
prox. five times manually in and out.
CAUTION
Remove rubber hose
If the rubber hose is not removed, the head will crash!
Maintenance Tasks for C&P20/A/M/P Head
Performing Maintenance Tasks 4.6.5 Oiling the DP Driver Bearing
50 Maintenance Manual SIPLACE Placement Heads CPP, C&P20, Twin
4.6.5
4.6.5 Oiling the DP Driver Bearing
Oiling the DP Driver Bearing
► C&P20: For this maintenance task, use the white combitip with Nye Synthetic Oil 200A.
► C&P20A/M/P: For this maintenance task, use the black combitip with Klüberalfa DH 3-100.
► Set the multipette to 1 µl.
► Rotate the star three times and wipe away any lubricant which appears with the blotting paper.
► Fit the removed nozzle back into place.
► Remove the blotting paper.
► Rotate the star so that segment 1 can be seen in the
center of the service hole.
► Carefully push a strip of blotting paper (1) under the
service hole (2) between the head housing and the
raceway. The blotting paper should soak up any ex-
cess oil.
► Mark the first segment by removing a nozzle.
► Clean the bearing with a cleaning stick.
► Position the multipette on the top edge of the locking
pin and apply 1 µl of lubricant.
Repeat this step for all segments.
Maintenance Tasks for C&P20/A/M/P Head
4.6.6 Vacuum Operation: Maintenance Tasks on Vacuum-Conducting Parts Performing Maintenance Tasks
Maintenance Manual SIPLACE Placement Heads CPP, C&P20, Twin 51
4.6.6
4.6.6 Vacuum Operation: Maintenance Tasks on Vacuum-Conducting Parts
Vacuum Operation: Maintenance Tasks on Vacuum-Conducting Parts
NOTICE
Vacuum test
► When carrying out the following tasks, especially check the segments that were noticeable
during the vacuum test.
NOTICE
Camera lens system
► Make sure that you do not damage or contaminate the camera lens system.
NOTICE
Silencer or reflecting ring
A reflecting ring is fitted in place of the silencer for vacuum pump operation.
Cover (C&P20 P shown as example)
► Loosen the screw fastening the cover and remove the
cover.
Reflecting ring (C&P20 P shown as example)
► Remove the three protruding screws (1) from the re-
flecting ring.
► Carefully lever the reflecting ring off the locating pins.
Make sure that the O-ring is not damaged.
► Clean the seat of the reflecting ring with a lint-free
cloth, if required.
CAUTION!
DO NOT use compressed air!