00197551-01_MM_CPP-CP-Twin_Kunde_en - 第75页
Maintenance Tasks for Holding Circuit Tools, Consumables, Spare and Wear Parts Maintenance Manual SIPLACE Placement Heads CPP, C &P20, Twin 75 7 7 M a in t e n a n c e T a s k s f o r H o ld in g C ir c u it Maintena…
Maintenance Tasks for Pressure Control Valve
Performing Maintenance Tasks 6.3.1 Checking/Cleaning the Pressure Control Valve
74 Maintenance Manual SIPLACE Placement Heads CPP, C&P20, Twin
► Fit the cover plate into place with the three fastening screws. Tighten the fastening screws with a
torque of 0.2 Nm.
Fitting the board board
► Position the two white plastic spacers onto the body
of the valve.
► Make sure that the sensor (3) slides smoothly into the
opening (2) in the housing.
Fastening the long board
► Fix the long board (2) into place with the two fasten-
ing screws (1). Tighten the fastening screws with a
torque of 0.2 Nm.
CAUTION!
The fastening screws for the boards are self-tapping
screws.
Make sure that no new thread is created when screwing
in the screws.
Turn the screws first to the left, in order to use the start of
the existing thread.
Maintenance Tasks for Holding Circuit
Tools, Consumables, Spare and Wear Parts
Maintenance Manual SIPLACE Placement Heads CPP, C&P20, Twin 75
7
7 Maintenance Tasks for Holding Circuit
Maintenance Tasks for Holding Circuit
7.1
7.1 Tools, Consumables, Spare and Wear Parts
Tools, Consumables, Spare and Wear Parts
The following lists contain all necessary consumable materials, wear and spare parts plus tools for clean-
ing the holding circuit.
Consumables Item no. HMK
Lint-free cloth, KM wipe 03082092- xx
Ethanol
Isopropanol – IPA can be used as an alternative.
Distilled water
Compressed air
Protective latex gloves 00372972- xx
Anti-static plastic cleaner and care product (http://www.burnus.de)
Isopropanol – IPA can be used as an alternative.
Ultrasound cleaning agent Alsar 25NKF 03110147- xx
Wear parts Item no. HMK
CPP only:
Set of seals for holding circuit (for CPP and CP20x) 03095007- xx
Tools Item no. HMK
ESD wriststrap TYP.OK/WRS 00320279- xx
Multipipette (replaces: [03078989-xx]) 00386154- xx X
Combitips 10 µl orange 03109540- xx X
Ultrasound device
SIPLACE recommends that you use the following ultrasound device
and accessory parts from BANDELIN electronic (http://www.bande-
lin.com):
▪ Ultrasound device SONOREX SUPER RK 510 [order no. Ban-
delin: 327]
▪ Clip-on basket K 10 [order no. Bandelin: 359]
▪ Handle adjustment GV 10 for baskets (one pair) [order no. Ban-
delin: 092]
▪ Lid D 510 [order no. Bandelin: 3008]
Spare parts Item no. HMK
CPP only:
Holding circuit assembly for CPP version <= 04 03055424- xx
Holding circuit assembly for CPP version >= 05 03081381- xx
C&P20/A/M/P only:
Holding circuit assembly C&P20 03005123- xx
Maintenance Tasks for Holding Circuit
Preparatory Steps 7.3.1 CPP: Cleaning/Checking the Holding Circuit
76 Maintenance Manual SIPLACE Placement Heads CPP, C&P20, Twin
7.2
7.2 Preparatory Steps
Preparatory Steps
► Prepare the ultrasound bath.
7.3
7.3 Performing Maintenance Tasks
Performing Maintenance Tasks
7.3.1
7.3.1 CPP: Cleaning/Checking the Holding Circuit
CPP: Cleaning/Checking the Holding Circuit
CAUTION
Safety data sheet
► Observe the safety data sheet for the cleaning fluid used.
NOTICE
Recommendation
We recommend that you have an additional holding circuit available, so that this can be easily
replaced during head maintenance.
► Remove the sealing ring (1) and the sealing disk (2)
and clean them with a lint-free cleaning cloth. Check
the sealing ring and the sealing disk for damage and
replace them if necessary (set of seals for holding cir-
cuit/CPP [03095007-xx]).
► Clean the holding circuit with a lint-free cleaning
cloth.
You can also use an anti-static plastic cleaner for bet-
ter cleaning results.