ServiceInstruction_Vision XP - 第141页

V ISION XP+ V AC Page 137 Index Operating Instructions V ersion 1.5 Index A Additional cle aning chute VXP+ .. ..................... 28 Adjusting th e Center Support ...... ................... 114 Adjusting th e Conveyor…

100%1 / 142
Page 136 VISION XP+ VAC
List of Tables
Operating Instructions
Version 1.5
VISION XP+ VAC Page 137
Index
Operating Instructions
Version 1.5
Index
A
Additional cleaning chute VXP+.......................28
Adjusting the Center Support.........................114
Adjusting the Conveyor Side Panels..............112
Adjustment .......................................................64
Adjustment Default Values.............................123
Adjustment, Inspection...................................111
Alarm Configuration .........................................81
Alarm Configuration Default Values...............124
Alarm Type.......................................................81
B
Back of plant below the vacuum chamber .......36
Backup Tool...................................................105
C
Chain Lubricator...............................................80
Chain Lubricator - Checking and Refilling the
Tank .............................................................57
Chain Lubricator - Replacing the Felt Wheels .58
Chain Lubricator Default Values ....................129
Chain oiler maintenance VXP+........................58
Check that the vacuum chamber is sealed ......33
Check the chain slack ......................................37
Check the fill level of the vacuum pump and top
up (The pump is operated with PFPE liquid)41
Checking and Adjusting Nitrogen Pressure ...121
Checking Center Support Position.................113
Clean cooling module 1 VXP+ .........................29
Clean the vacuum pump..................................43
Clean trapped heat cooler................................30
Cleaning of coated nozzle fields ......................20
Cleaning of Condensate Trap VXP..................46
Cleaning of oven stations.................................16
Cleaning the Catch Pans .................................48
Cleaning the Control Cabinet...........................60
Cleaning the Cooling zone...............................27
Cleaning the Curtains ......................................22
Cleaning the Exhaust Filters at the Inlet and the
Outlet............................................................44
Cleaning the Gauze Filter ................................47
Cleaning the Guide Rails for the Sheet Metal Co-
vers...............................................................21
Cleaning the Interior.........................................15
Cleaning the nozzle holder (VXP+)..................18
Cleaning the Process Chamber .......................14
Cleaning the Seal.............................................23
Cleaning the Sensors.......................................59
Cleaning Work at the Cooler Units.............49, 50
Complete Maintenance Check ........................ 61
Condensate Trap ............................................ 46
Configuration Activ Energy Meters................ 109
Consumption Parameter ................................. 96
Conveyor......................................................... 75
Conveyor Adjustment...................................... 77
Conveyor Default Values .............................. 128
Conveyor Drive ............................................... 75
Conveyor Drive Parameter Default Values ... 129
Conveyor System............................................ 57
Cooling Tract................................................... 27
D
Default Values............................................... 123
Default Values Consumption Parameters ..... 131
Default Values Filter F9 Parameter............... 131
Default Values Nitrogen control .................... 130
Detail view of the vacuum chamber ................ 32
Dual track vacuum chamber settings .............. 34
E
EC – Check gas blower................................... 25
Electrical Safety Inspection ............................. 61
Exchange of activated carbon......................... 55
Exhaust Air Monitoring .................................. 117
F
Fan Parameters .............................................. 93
Fans Monitoring Default Values .................... 127
Filter F9 Parameter ......................................... 97
Flux Management Parameter.......................... 74
Frequency Converter ...................................... 84
Frequency Converter Parameter Default Values
126
G
Gas take-off point
– N2 regulation ............................................... 53
General Notes ................................................... 7
H
Heater Parameters.......................................... 67
I
Inspecting and Cleaning the Fan Impeller 28, 29,
30
Inspecting Conveyor Width for Parallelism ... 111
Interface Default Values................................ 128
Introduction ....................................................... 3
Seite 138 VISION XP+ VAC
Index
Operating Instructions
Version 1.5
M
Maintenance...................................................... 7
Maintenance intervals for the vacuum pump .. 42
Maintenance Schedule.................................... 10
Maintenance Schedule Nitro ........................... 10
Monitoring the Water Flow Rate.................... 119
N
N2 Operating Parameters ............................... 94
O
Opening Times................................................ 61
Optical fibre sensor at the inlet area ............... 14
Optical fibre sensors before and after the vacuum
chamber....................................................... 39
Overall System................................................ 61
P
Possible Alarm Types ..................................... 82
Pre-Filter (Residual Oxygen Meter) ................ 54
Proceeding
– CBS-position................................................ 79
Proceeding calibration of PCB-width............... 78
Process chamber ............................................ 15
Pyrolysis.......................................................... 51
R
Recommendations for the use of chemical clea-
ning agents .................................................... 7
Regulating the Coolant Water Circuit............ 120
Replacing the Activated Carbon Filter............. 55
Replacing the Fan Impeller ............................. 31
Replacing the Granulate ................................. 51
Replacing the Seal.......................................... 24
Residual Oxygen Meter................................... 54
Response Time ............................................... 81
Revision Levels................................................. 3
S
Safety Precautions ............................................ 4
Service Department Address .......................... 61
Service Hotline ................................................ 61
Settings for Individual Components............... 103
Setup Instructions............................................ 63
Siemens Type MM 420 with Profibus - Connec-
tions ............................................................. 91
Single track vacuum chamber settings............ 35
Smoking ban ..................................................... 5
Standby Duty................................................... 61
T
Teaching of Ultrasonic Sensor Inlet and Outlet...
115
Temperature Channels.................................... 67
Typ Mitsubishi FR-D 700
– B&R Control................................................. 85
– Siemens....................................................... 88
U
Uninstalling the EC gas blower ....................... 26
V
Vacuum chamber service.............................. 100
Vacuum chamber transfer height .................... 33
Vacuum parameters ...................................... 102
Vacuum pump filter ......................................... 40
Vacuum pump oil level .................................... 40
Vacuumunit ..................................................... 32
Volume flow control, cooling section parameters
98
W
Warning Time .................................................. 81
Watchdog Parameters..................................... 72
Water Tank - Checking and Refilling the Water
Fill-Level ...................................................... 45