EdisonStandardOwnersManual-RevA-20170818B - 第55页
Edison Printer User Manual (Part Number 1023838) I NSTALLATION AND I NITIA L S T A RT - U P Rev. A 55 Copyright © 2017 ITW EAE All rights reserved. No part of the contents of this manual may be reproduced, copi ed or tra…
INSTALLATION AND INITIAL START-UP Edison Printer User Manual (Part Number 1023838)
54 Rev. A
Copyright © 2017 ITW EAE
All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any
means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and
retrieval systems without the written permission of ITW EAE, unless for purchaser's personal use.
3.3.4.3. Interface Cable Installation
Follow this procedure to install printer SMEMA (Surface Mount
Equipment Manufacturers Association) interface cables. Review the
Interface Schematic (1021368) for the interface of preceding (Upstream)
and succeeding (Downstream) machines.
1. Set printer power to OFF.
2. Remove the two interface cables (Qty. 2 of P/N: CA-1004) from the shipping kit
supplied with the printer.
3. Plug the cables (Upstream and Downstream) into the SMEMA
connectors located inside the hood just above the pneumatics door.
4. Route both cables out through the bottom of the printer and to their
destination machines.
Attention
Before the installation is considered complete and the printer
fully operation, an ITW EAE representative must calibrate the
printer and complete the installation checklist.
3.4. Remove Transit Material
Edison printer assemblies may be secured with cable ties, packing material, and shipping brackets
to protect them during transit. Remove these materials and associated Remove Before Operation
(RBO) tags prior to printer operation (Figure 29).
Figure 28. Upstream and
Downstream SMEMA
connectors
Figure 29. Remove Before Operation Tags.
Edison Printer User Manual (Part Number 1023838) INSTALLATION AND INITIAL START-UP
Rev. A 55
Copyright © 2017 ITW EAE
All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any
means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and
retrieval systems without the written permission of ITW EAE, unless for purchaser's personal use.
3.4.1. Hood Blocks
Remove the two foam blocks from between the hood and the side covers.
3.4.2. Table Lift Brackets
Remove the two table lift shipping brackets and the RBO tags at the rear of the rear table
assembly (Figure 30).
3.4.3. Vision XY Bracket
Remove the one Vision XY shipping bracket and associated RBO securing the vision gantry to
the right side of the printer frame, as viewed from the rear of the
printer.
Figure 30. Remove Table Lift Brackets.
Figure 31. Remove Vision
XY Bracket.
INSTALLATION AND INITIAL START-UP Edison Printer User Manual (Part Number 1023838)
56 Rev. A
Copyright © 2017 ITW EAE
All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any
means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and
retrieval systems without the written permission of ITW EAE, unless for purchaser's personal use.
3.4.4. Wiper Bracket (Front)
Remove the two front wiper shipping brackets and RBO tags
securing the wiper to the frame (Figure 32).
3.4.5. Wiper Bracket (Rear)
Remove the rear wiper shipping bracket and RBO tag, located
behind the take-up roll (Figure 33).
3.4.6. Panel Support Blocks (Front and Rear)
Lift the front panel support and remove the two foam
blocks from between the panel support and the work table.
Repeat for the rear panel support (Figure 34).
Figure 32. Remove two front wiper
shipping brackets.
Figure 33. Remove rear wiper shipping
bracket.
Figure 34. Remove panel support blocks--front
& rear.