EdisonStandardOwnersManual-RevA-20170818B - 第75页
Edison Printer User Manual (Part Number 1023838) P ROCESS P ROGRA M C REATION Rev. A 75 Copyright © 2017 ITW EAE All rights reserved. No part of the contents of this manual may be reproduced, copi ed or transmi tted in a…
PROCESS PROGRAM CREATION Edison Printer User Manual
74 Rev. A
Copyright © 2017 ITW EAE
All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any
means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and
retrieval systems without the written permission of ITW EAE, unless for purchaser's personal use.
4.2.5. Dispense Program Data
Dispense program data determines how to handle adding paste to the stencil (Figure 48). Use
Dispense Program Data to select the profile of the dispensing material. Selections include:
Material type: Ink, adhesive, solder paste
Auto Dispense: Number of passes, Speed (of passes), Delay (delay start of dispense cycle),
Frequency (print cycles), Left Edge +/- (offset before dispensing), Right Edge +/ - (offset
before dispensing)
Check Prompt user to check paste to set the frequency at which the user should manually
check paste levels. The value displays on the home screen when the printer is in production mode.
The value reduces incrementally (by one) after every print and at zero prompts the user (in the
Alert section) to check the paste.
Figure 48. Dispense Program Data.
4.2.6. Print Head Program Data
Print Head Program Data determines the detailed movement of the print head. Selections include:
Common (Figure 49):
o Positive stroke: Press Calculate Stroke to automatically fill the value. The software
calculates stroke length based on panel size.
o Negative stroke: Press Calculate Stroke to automatically fill the value. The
software calculates stroke length based on panel size.
o Print strokes: Enter number of desired print strokes.
o Print Strokes After Wipe: Enter number of desired print strokes after the wipe.
Edison Printer User Manual (Part Number 1023838) PROCESS PROGRAM CREATION
Rev. A 75
Copyright © 2017 ITW EAE
All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any
means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and
retrieval systems without the written permission of ITW EAE, unless for purchaser's personal use.
Squeegee (Figure 49):
o Print force: Press Calculate Force to automatically fill the value. The software
calculates force based on panel size.
o Print Speed: Enter desired print speed (mm/s)
o Blade Gap: Enter desired blade gap (mm)
o Post Print Up Delay: Enter desired delay (ms)
o Post Print Lift Height: Enter desired height (mm)
o Post Print Lift Speed: Enter desired speed (mm/s)
o Hop Height: Enter Desired height (mm)
o Hop Distance: Enter desired distance (mm)
o Stroke Type: Select from pull-down menu selections include Normal, Flood/Print,
Print/Flood
o Flood Gap: Enter desired gap (mm)
o Flood Speed: Enter desired speed (mm/s)
Figure 49. Process Program Data Screen 1.
Head Offsets (Figure 50)
o Check Enabled to allow offsets
o Enter desired Force Offset and Speed Offset.
o Click Apply Offsets.
Paste (Figure 50):
o Check Paste height monitoring to allow monitoring
o Enter desired Low threshold
o Select Add paste mode from drop down menu
o Check Enabled Critical Threshold to enable
PROCESS PROGRAM CREATION Edison Printer User Manual
76 Rev. A
Copyright © 2017 ITW EAE
All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any
means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and
retrieval systems without the written permission of ITW EAE, unless for purchaser's personal use.
Enter desired Critical Threshold.
Knead (Figure 50):
o Click Enable on First Panel to allow paste kneading on first panel
Figure 50. Process Program Data Screen 2