00197465-01_SM_CP20-A-M_EN - 第42页
3 Service Work Conveyor 3.12 Replacing the Z Drive [03058631-xx] 42 Service Manual SIPLACE C&P20, C&P20A, C&P20M 3.12 3 . 1 2 R e p la c in g t h e Z D r iv e [ 0 3 0 5 8 6 3 1 - x x ] Replacing the Z Drive […
3 Service Work Conveyor
3.11 Replacing the Component Sensor [03006742-xx]
Service Manual SIPLACE C&P20, C&P20A, C&P20M 41
► Loosen the two fastening screws (4) and remove the complete component sensor (3).
Installation
► Install the new component sensor. Tighten the fastening screws with a torque of 130 Ncm.
► Reconnect to the electricity system. Fasten the cable with cable ties.
► Fit the Z axis with return unit and the pressure control valve.
► Perform a reference run.
NOTICE
Do not separate the transmitter and receiver unit
The components of the transmitter and receiver unit are coordinated with one another. Only
loosen the two fastening screws, otherwise the component sensor will no longer function prop
-
erly.
NOTICE
Reference run
If the reference run fails, you will need to check the settings for the jaws on the Z drive.
3 Service Work Conveyor
3.12 Replacing the Z Drive [03058631-xx]
42 Service Manual SIPLACE C&P20, C&P20A, C&P20M
3.12
3.12 Replacing the Z Drive [03058631-xx]
Replacing the Z Drive [03058631-xx]
Parts, equipment and tools
▪ Z drive complete C&P20A [03058631Sxx] (for C&P20, C&P20A and C&P20M)
▪ Magnet removal plate C&P20A [03078491-xx]
▪ Torque screwdriver 100-500 Ncm [03078400-xx]
▪ Extension/straight TX20 [03073256-xx]
▪ Tools for removing the head, if needed (see also the service manual for your machine)
Overview
NOTICE
Intermediate distributor board
The package from FS05 contains the intermediate distributor board [03002942-10] in addition.
Also this board has to be exchanged, if required (s.u.)
Overview of C&P20A head
1. Pressure control valve
2. Return unit
3. Z axis
4. Z axis drive cover
Overview of Z drive
1. Complete Z drive
2. 2 x fastening screws
3. Light barrier Z drive down
4. Snap jaws
1
3
2
4
1
4
3
2
3 Service Work Conveyor
3.12 Replacing the Z Drive [03058631-xx]
Service Manual SIPLACE C&P20, C&P20A, C&P20M 43
Preparation
► Remove the head from the machine. For removal and installation details of the placement head, read
the service manual for your machine.
Removal/installation
NOTICE
Also the intermediate distributor board has to be exchanged, if required
Z drives from FS05 are using the connector X6 with another shape.
► If a Z drive FS < 05 is replaced with a Z drive FS >= 05, also the intermediate distributor
board must be replaced.
See section "3.9 Replacing the intermediate distributor board [03002942-xx] on the
C&P20A head" [ ➙ 30]
► Dismantle the cover plate (1) over the Z axis. Loosen
the screws at (2) and (3). Carefully remove the cover
plate.
CAUTION!
Take care not to damage the component sensor prisms.
► Use the magnet removal plate (1) to remove the two
magnets (3).
CAUTION!
If the magnets are stuck in place, you can press these out
from above (2) with a pointed object. If you damage the
foil while removing the magnets, you will need to also re
-
place the foil.