4OM-1003-007 - 第232页
(05 T able X) Error ID Item Description 050101 T able-X Axis Origin Encoder origin was not detected. (Cause 1) The encoder section of the motor may be defective or the encoder cable may be broken. (Remedy 1) T urn off th…
Error ID Item Description
04060c Comp. Place. (Z) Axis Servo off time out
Servo Error
04060d Comp. Place. (Z) Axis Servo power off
Servo Error
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
040701 Comp. Place. (Z) Axis Interlock Movement cannot take place until the index angle is adjusted.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
040801 Comp. Place. (Z) Axis Communication error was detected.
Communication
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
0511-002 2-51 AIL01ETRP
3.3 Error IDs and Remedial Procedures
(05 Table X)
Error ID Item Description
050101 Table-X Axis Origin Encoder origin was not detected.
(Cause 1) The encoder section of the motor may be defective or the encoder cable may be
broken.
(Remedy 1) Turn off the power and check for looseness of the connector section for the signal
cable.
If the error is not canceled yet after this check operation, the broken signal cable
or the motor may be defective. Consult our service personnel for the remedy.
050102 Table-X Axis Origin Origin sensor (slide) was not detected.
(Cause 1) The sensor may be defective or the cable may be broken.
(Remedy 1) Press the [RETURN] button to cancel the error display and then the [ALL] button
entitled "ZERO".
If the error cannot be canceled after the zeroing operation, it is required to re-
place the sensor or the sensor cable with a new one. Consult our service person-
nel for details.
050103 Table-X Axis Origin Origin sensor (slide) and Limit error has been detected.
050104 Table-X Axis Origin Feedback value is indefinite.
050105 Table-X Axis Origin The component pick-up (z) axis is not at origin.
050201 Table-X Axis Timing Task has not been completed unable to continue.
050301 Table-X Axis Data The driver data was detected outside of the possible range.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service per
sonnel for the remedy.
0511-002 2-52 AIL01ETRP
3.3 Error IDs and Remedial Procedures
Error ID Item Description
050401 Table-X Axis Limit (+) Limit error has been detected.
050402 Table-X Axis Limit (-) Limit error has been detected.
(Cause 1) An optical beam of the sensor is shielded.
(Cause 2) Dirt adheres to the sensor and the optical beam is shielded.
(Remedy 1) Turn off the power supply and move the X/Y table to the position where opera
tions can be performed more easily.
Re-attach the light shield plate and the sensor securely (remove the looseness).
Re-supply power to the machine and perform the zeroing operation.
(Remedy 2) Wipe off dirt on the sensor and re-perform the zeroing operation.
050502 Table-X Axis Servo Alarm User constant breakdown.
[Shutdown touch sw key and mainbreaker sw off.]
050503 Table-X Axis Servo Alarm Main circuit encoder error
050504 Table-X Axis Servo Alarm User constant setting error.
[Shutdown touch sw key and mainbreaker sw off.]
050505 Table-X Axis Servo Alarm Combination error
050509 Table-X Axis Servo Alarm Dividing ratio setting error.
[Shutdown touch sw key and mainbreaker sw off.]
05050a Table-X Axis Servo Alarm Encoder model unmatched.
[Shutdown touch sw key and mainbreaker sw off.]
050510 Table-X Axis Servo Alarm Overcurrent or Heat Sink Overheated.
[Shutdown touch sw key and mainbreaker sw off.]
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
0511-002 2-53 AIL01ETRP
3.3 Error IDs and Remedial Procedures