2OM-1075-002.pdf - 第235页

AHB01ESPP 2 . 1 "Zeroing Opn." T ab The corresponding tab sheet enables the operator to zero each device (axis). • Sheet Layout When the "Zeroing Opn." tab is pressed in the "MNL OPN." windo…

AHB01ESPP

2. "MNL OPN." Window (Submenu)

• Window Layout

When the [MNL OPN.] button on the submenu bar of the "MAINT." win-

dow is pressed, the following window (submenu) opens.

Fig. 2F3 "MNL OPN." Window (Submenu)

(Provided with Multi-Layer Tray Feeder 2)

The tab sheet may look different, depending on which options

are selected.

• Window Composition

*1 Tabs and Tab Sheets

The "MNL OPN." window (submenu) is provided with the following 2

tabs. When a tab is pressed, the corresponding tab sheet appears

inside the window.

Table 2F1

Tabs Description

Zeroing Opn. The corresponding tab sheet enables the operator to zero each de-

vice.

Manual Axis Opn. The corresponding tab sheet enables the operator to perform the

manual alignment of each device.

01 12-002 6 - 5

2. "MNL OPN." Window (Submenu)

Note

AHB01ESPP

2.1 "Zeroing Opn." Tab

The corresponding tab sheet enables the operator to zero each device

(axis).

• Sheet Layout

When the "Zeroing Opn." tab is pressed in the "MNL OPN." window

(submenu), the following tab sheet opens.

Fig. 2F4 "Zeroing Opn." Tab Sheet

(Provided with Multi-Layer Tray Feeder 2)

The tab sheet may look different, depending on which options

are selected.

• Sheet Composition

*1 Select Unit Buttons

The following buttons are provided.

[Beam X1 Axis] Button

[Beam X2 Axis] Button

[Beam Y Axis] Button

[Support Pin Axis] Button

[Conv. Wid. Adj. Axis] Button

[Tray2 Axis] Button (Option)

[Up/Down Axis] Button in "Head #1" Group Box

[Rotational Axis] Button in "Head #1" Group Box

[Nozzle Change Axis] Button in "Head #1" Group Box

[Up/Down Axis] Button in "Head #2" Group Box

01 12-002 6 - 6

2.1 "Zeroing Opn." Tab

Note

AHB01ESPP

[Rotational Axis] Button in "Head #2" Group Box

[Nozzle Change Axis] Button in "Head #2" Group Box

When a button is pressed, the background color turns yellow, indi-

cating that the device (axis) is selected.

Pressing the button again changes the background color to the origi-

nal one, indicating that the selection is canceled.

Each button has a box on the right side and the status of the corre-

sponding device is indicated in the box.

Refer to "Notes" in "*5".

Two or more devices can be selected.

*2 "All" Group Box

It is indicated whether or not all devices are zeroed.

"---" : All devices are not zeroed.

"Origin" : All devices are zeroed.

*3 [Select All] Button

When this button is pressed, all devices (possible to be returned to

their origins) are selected and the corresponding buttons turn yel-

low.

The [Select All] button cannot be used to select the [Sup-

port Pin Axis] and [Conv. Wid. Adj. Axis] buttons.

*4 [Cancel All] Button

When this button is pressed, the selection of all devices is can-

celed.

*5 Control Switch

When the [ENABLE] button on the operation panel is pressed in two

seconds after a device(s) is selected and the [ON] button (entitled

"MOVE") is pressed, the device is zeroed.

(a) After the zeroing operation is completed, "Origin" ap-

pears in the box on the right side of the corresponding

button.

(b) When the current position is being managed or indefi-

nite, "---" appears in the box.

Note

01 12-002 6 - 7

2.1 "Zeroing Opn." Tab

Note