2OM-1075-002.pdf - 第320页

AHB01ESPP *9 [Cancel] Button When pressed, this button ends the teaching operation without re- flecting the teaching results on the offset data. *10 [End] Button When this button is pressed, the "Confirmation" …

AHB01ESPP

*5 Set Status

When the "P.E.C. Dsbl." or the "Comp. Recognition Dsbl." check

box in the "Test Run" tab sheet is turned on (checked), the back-

ground color of "Recognition Dsbl." turns light red. (No background

color in normal cases).

No recognition processing is made even if a teaching op-

eration is performed when each check box is turned on

(checked) in the "Test Run" tab sheet. Therefore, various

teaching operations will get incorrect results.

When "All Beam (Incl. NC Axis) Heads Zero" is completed, the back-

ground color of "All Beam Zero" turns green. (Otherwise, the back-

ground has no color.)

(a) When each device is not zeroed and the teaching op-

erations are performed, note that the offset values may

not be taught correctly.

(b) Before performing a teaching operation, be sure to zero

all beams.

*6 Offset Values

Displayed are the current values and the adjusted ones after teach-

ing.

*7 [Nozzle Set/Reset] Button

When this button is pressed, the "Nozzle Set/Reset" sheet appears,

enabling the cycle operation for opening or closing the nozzle stocker

and attaching or storing a vacuum nozzle through manual opera-

tions.

Refer to "4.4 "Nozzle Change" Tab" for details.

*8 [Clear Adj.] Button

When this button is pressed, the following "Confirmation" dialog box

opens.

Fig. 2F59

When the [YES] button is pressed, the adjusted values are cleared.

When the [NO] button is pressed, the adjusted values are not cleared.

5.1 "Pick-Up Location" Tab

Note

0206-003 6-87

AHB01ESPP

*9 [Cancel] Button

When pressed, this button ends the teaching operation without re-

flecting the teaching results on the offset data.

*10 [End] Button

When this button is pressed, the "Confirmation" dialog box opens.

Fig. 2F60

When the [YES] button is pressed, the results of the teaching op-

eration are reflected on the offset data and the dialog box closes.

When the [NO] button is pressed, the dialog box closes without re-

flecting the results of the teaching operation on the offset data.

*11 "Control Switch" Group Box

When the [ENABLE] button on the operation panel is pressed in two

seconds after one of the buttons in the "Select Mode" group box (*4)

and the [ON] button (entitled "MOVE"), the selected action takes

place.

*12 [Return] Button

When this button is pressed, the "Tape, Vib. Stick Teach Pick-Up

Pos. [Comp. Center Pos.]" sheet disappears and the "Pick-Up Lo-

cation" tab sheet appears.

5.1 "Pick-Up Location" Tab

0206-003 6-88

AHB01ESPP

••

• Teaching Operation for Alignment of Component Center with

Vacuum Nozzle Center

Perform this teaching operation when no regulation is given to the shape

of components and positioning should be made simply to the compo-

nent center.

The teaching operation must be performed with "All Beam Zero"

being displayed.

(1) Follow the teaching procedure below to perform the teaching op-

eration on the component center position.

Teaching Procedure

Selection of [Tape, Vib. Stick Teach Pick-Up

Pos. [Comp. Center Pos.]] Button

Selection of Head

Setting of Objective Feeder No. for Teaching

Refer to "5.1.4 "Feeder No. Set" Sheet"

for details.

Selection of "Center 1-Pt." or "Diagonal 2-Pt."

Suitable for Component Size

Selection of [Teach Pick-Up Pos.

[Comp. Center Pos.]] Button

Press the [ENABLE] button on the operation

panel in two seconds after the [ON] button

(entitled "MOVE").

The placement head moves to the objective feeder

position for teaching and the image of the pick-up

position is captured by the P.E.C. camera.

In the case of "Center 1-Pt.", the registration of the

designated nozzle is made together for graphic

teaching to facilitate the manual alignment opera-

tion with the pointing device.

Positioning Operation with Pointing Device

Refer to "Pointing Device Operation" (described

later) for details.

Selection of [End] Button

Selection of [YES] Button in "Confirmation"

Dialog Box for Replacement of Offset Data

Fig. 2F61

5.1 "Pick-Up Location" Tab

Note

0206-003 6-89