2OM-1075-002.pdf - 第376页
AHB01ESPP (2) Editing of Parameters • Editing of Numerical V alues Numerical values can be changed with the increment/decrement keys or the ten-key pad. T able 2F18 Keys Functions Use these keys to increment or decrement…
AHB01ESPP
Table 2F17
Component Shape Example of Graphic Representation Displayed Parameters
BGA (Normal) A: Mold size X [mm], Y [mm]
B: Component Center
Center of Mold Size X, Y
C: Each Ball Data
Diameter : Ball Diameter
Position : Each Ball Group
Calculated based on
each ball group data
During Data Editing A: Mold size X [mm], Y [mm]
B: Component Center
Center of Mold Size X, Y
C: Each Ball Data
Diameter: Ball Diameter
Position : Calculated based on
each ball group data
Yellow : Balls in Object Group for
Editing
Green : Balls in Other Block
(block other than object
one for editing)
D: Each Missing Ball Data
Diameter: Ball Diameter
Position : Calculated based on
each ball group data
Light Blue :
Balls in Object Missing
Block for Editing
Red : Balls in Other Missing
Block (missing block
other than object one for
editing)
Note: All missing balls are expressed
in red in any edit windows other
than the edit window for the
missing ball data.
5.2 Library Teaching
0308-004 6-143
A (Green)
C (Green)
B (Light Blue)
D (Red, Light Blue)
A (Green)
C (Green)
B (Light Blue)
AHB01ESPP
(2) Editing of Parameters
• Editing of Numerical Values
Numerical values can be changed with the increment/decrement keys
or the ten-key pad.
Table 2F18
Keys Functions
Use these keys to increment or decrement a numerical value.
The graphical representation changed according to the increment or
the decrement of the numerical value.
When pressed, this button opens the ten-key pad window.
• Parameter Entry with Ten-Key Pad
Fig. 2F104-18
Table 2F19
Keys Functions
0 to 9, ., - These keys can be used to enter numerical values.
C This key can be used to clear the current numerical value to "0"
OK This key defines the numerical value and closes the window.
Cancel This key interrupts the setting and closes the window.
When an improper parameter is specified, an error message is issued
in the message box, indicating that the entered parameter is not ac-
cepted.
In this case, press the [C] key to clear the parameter and re-enter a
correct value (a value that meets the specified range).
Message:
• Out of Range: The specified value is out of the range.
0308-004 6-144
Message Box
5.2 Library Teaching
AHB01ESPP
• Change of Selected Parameter
Fig. 2F104-19
To change the selected parameter, select one of the check boxes.
A yellow check box indicates that it is selected.
Click the check box (item) to be selected and press the [OK] button.
The selected check box turns yellow, indicating that the item is selected
(specified).
(3) Other Functions
The following shows the functions that can be used for editing, etc.,
of parameters.
• Graphic Relocation Function
1) To relocate the graphic roughly, using the adjuster
Change of Position X/Y:
Move the cursor to the center of the adjuster as shown
in the left figure and click the center. The graphic can be
moved in the X and Y directions.
When you click the center again after the relocation, the
position is defined.
Change of Angle θ :
Move the cursor close to the arrow tip of the adjuster as
shown in the left figure and click the tip. The angle (theta)
of the graphic can be changed.
When you click the tip again after the angle is changed,
the angle is defined.
2) To relocate the graphic finely with the keys
The graphic can be relocated more finely than the adjuster.
Table 2F20
Keys Functions
The graphic can be moved in the selected direction.
The graphic can be rotated in the selected direction.
5.2 Library Teaching
0308-001 6-144-1