2OM-1075-002.pdf - 第380页

AHB01ESPP • Sheet Composition *1 "Select Option" Group Box Select the head to be used for teaching operations. The following buttons are provided in this group box. [All Heads] Button The machine performs the t…

AHB01ESPP

5.3 "P.E.C. Recog Camr & Beam Ofs" Tab

The corresponding tab sheet enables the operator to perform the teach-

ing operation on the P.E.C. recognition camera & X/Y beam offset data.

The offset values are calculated by recognizing the printed pattern on

the positioned special jig P.C.B. (option) with the P.E.C. recognition cam-

era.

Determine the magnification and tilting (Theta Z) of the P.E.C. recogni-

tion camera and the tilting of the beam (Angles X and Y).

This teaching operation must be performed only by our service

personnel.

• Sheet Layout

When the "P.E.C. Recog Camr & Beam Ofs" tab is pressed in the

"TEACHING" window (submenu), the following tab sheet appears in-

side the window.

Fig. 2F105 "P.E.C. Recog Camr & Beam Ofs" Tab sheet

5.3 "P.E.C. Recog Camr & Beam Ofs" Tab

Note

0206-003 6-145

*10

*11

AHB01ESPP

• Sheet Composition

*1 "Select Option" Group Box

Select the head to be used for teaching operations.

The following buttons are provided in this group box.

[All Heads] Button

The machine performs the teaching operations on the offsets

of the P.E.C. recognition cameras on both X1 and X2 heads

and the beam offsets.

(a) The teaching operations are performed first on the X1

head and then the X2 head.

(b) Before performing any teaching operation, position the

jig P.C.B. and zero all beams.

[X1 Head] and [X2 Head] Buttons

When these buttons are pressed, the machine performs the

teaching operations on the offsets of the P.E.C. recognition

camera on the X1 or the X2 head and the beam offsets.

(a) The machine can perform the teaching operations re-

lated to only the X1 or the X2 head.

(b) Before performing any teaching operation, position the

jig P.C.B. and zero all beams.

[Camera-P1], [Beam Offset], [Camera-P2], and [Beam Offset]

Buttons

The machine performs an offset teaching operation for each

individual devices.

(a) Before performing any teaching operation, position the

jig P.C.B. and zero all beams.

(b) When a teaching operation must be implemented sepa-

rately, perform the teaching operation first on the cam-

era offsets and then the beam offsets. (To calculate

the beam offsets by using the results of the teaching

operation on the camera offsets)

Note

0206-003 6-146

5.3 "P.E.C. Recog Camr & Beam Ofs" Tab

AHB01ESPP

*2 Mode Selection Buttons

Various actions can be selected.

The following button is provided in this group box.

[All Beam (Incl. NC Axis) Heads Zero] Button

When this button is pressed, all X/Y beams are zeroed.

[Teach Start] Button

When this button is pressed, a teaching operation is performed on

the selected item.

[Chute Mark Recog.] Button

When this button is pressed, the fiducial mark on the chute is rec-

ognized to determine whether or not a teaching operation must be

performed.

When there is a big difference between the current and adjusted

values (results of chute mark recognition) in the display area of the

offset values (*4), it means that a teaching operation is required.

*3 Set Status

When the "P.E.C. Dsbl." or the "Comp. Recognition Dsbl." check

box in the "Test Run" window is turned on (checked), the background

color of "Recognition Dsbl." turns light red. (No background color in

normal cases)

No recognition processing is made even if a teaching op-

eration is performed when each check box is turned on

(checked) in the "Test Run" window. Therefore, various

teaching operations will get incorrect results.

When "All Beam (Incl. NC Axis) Heads Zero" is completed, the back-

ground color of "All Beam Zero" turns green. (Otherwise, the back-

ground has no color.)

(a) When each device is not zeroed and the teaching op-

erations are performed, note that the offset values may

not be taught correctly.

(b) Before performing a teaching operation, be sure to zero

all beams.

*4 Offset Values

Displayed are the current values and the adjusted ones after teach-

ing.

Note

0206-003 6-147

5.3 "P.E.C. Recog Camr & Beam Ofs" Tab