2OM-1075-002.pdf - 第381页

AHB01ESPP *2 Mode Selection Buttons V arious actions can be selected. The following button is provided in this group box. [All Beam (Incl. NC Axis) Heads Zero] Button When this button is pressed, all X/Y beams are zeroed…

AHB01ESPP

• Sheet Composition

*1 "Select Option" Group Box

Select the head to be used for teaching operations.

The following buttons are provided in this group box.

[All Heads] Button

The machine performs the teaching operations on the offsets

of the P.E.C. recognition cameras on both X1 and X2 heads

and the beam offsets.

(a) The teaching operations are performed first on the X1

head and then the X2 head.

(b) Before performing any teaching operation, position the

jig P.C.B. and zero all beams.

[X1 Head] and [X2 Head] Buttons

When these buttons are pressed, the machine performs the

teaching operations on the offsets of the P.E.C. recognition

camera on the X1 or the X2 head and the beam offsets.

(a) The machine can perform the teaching operations re-

lated to only the X1 or the X2 head.

(b) Before performing any teaching operation, position the

jig P.C.B. and zero all beams.

[Camera-P1], [Beam Offset], [Camera-P2], and [Beam Offset]

Buttons

The machine performs an offset teaching operation for each

individual devices.

(a) Before performing any teaching operation, position the

jig P.C.B. and zero all beams.

(b) When a teaching operation must be implemented sepa-

rately, perform the teaching operation first on the cam-

era offsets and then the beam offsets. (To calculate

the beam offsets by using the results of the teaching

operation on the camera offsets)

Note

0206-003 6-146

5.3 "P.E.C. Recog Camr & Beam Ofs" Tab

AHB01ESPP

*2 Mode Selection Buttons

Various actions can be selected.

The following button is provided in this group box.

[All Beam (Incl. NC Axis) Heads Zero] Button

When this button is pressed, all X/Y beams are zeroed.

[Teach Start] Button

When this button is pressed, a teaching operation is performed on

the selected item.

[Chute Mark Recog.] Button

When this button is pressed, the fiducial mark on the chute is rec-

ognized to determine whether or not a teaching operation must be

performed.

When there is a big difference between the current and adjusted

values (results of chute mark recognition) in the display area of the

offset values (*4), it means that a teaching operation is required.

*3 Set Status

When the "P.E.C. Dsbl." or the "Comp. Recognition Dsbl." check

box in the "Test Run" window is turned on (checked), the background

color of "Recognition Dsbl." turns light red. (No background color in

normal cases)

No recognition processing is made even if a teaching op-

eration is performed when each check box is turned on

(checked) in the "Test Run" window. Therefore, various

teaching operations will get incorrect results.

When "All Beam (Incl. NC Axis) Heads Zero" is completed, the back-

ground color of "All Beam Zero" turns green. (Otherwise, the back-

ground has no color.)

(a) When each device is not zeroed and the teaching op-

erations are performed, note that the offset values may

not be taught correctly.

(b) Before performing a teaching operation, be sure to zero

all beams.

*4 Offset Values

Displayed are the current values and the adjusted ones after teach-

ing.

Note

0206-003 6-147

5.3 "P.E.C. Recog Camr & Beam Ofs" Tab

AHB01ESPP

*5 Y2 Offset Difference

Shown are the values to be added to the Y-axis origin offset (Y2) for

tilting correction of the beam X axis.

After the teaching operation, the values must be used in the follow-

ing formula.

(X1+X2)/2

Enter the result in the "Y2 [mm]" text box in the "Y-Axis" tab sheet

that belongs to the "Offset Data" tab sheet in the "Machine System

Data - [Internal Editor]" window.

*6 [P.C.B. Transfer Manual Mode] Button

When this button is pressed, the "P.C.B. Transfer Manual Mode"

sheet appears.

Refer to "5.3.1 "P.C.B. Transfer Manual Mode" Sheet" for details.

*7 [Jig P.C.B.] Button

When this button is pressed, the "Jig P.C.B." sheet appears.

Refer to "5.3.2 "Jig P.C.B." Sheet" for details.

*8 [Clear Adj.] Button

When pressed, this button clears the results of the teaching opera-

tion.

*9 [Cancel] Button

When pressed, this button ends the teaching operation without re-

flecting the teaching results on the offset data.

*10 [End] Button

When this button is pressed, a "Confirmation" dialog box opens.

Fig. 2F106

When the [YES] button is pressed, the results of the teaching op-

eration is reflected on the offset data, and exits from this session.

*11 "Control Switch" Group Box

Select the items (buttons) to be taught and press the [ON] button

entitled "MOVE". After that, press the [ENABLE] button on the op-

eration panel in 2 seconds. A teaching operation is performed on

the selected item.

0206-003 6-148

5.3 "P.E.C. Recog Camr & Beam Ofs" Tab