2OM-1075-002.pdf - 第396页

AHB01ESPP (a) When each device is not zeroed and the teaching op- erations are performed, note that the offset values may not be taught correctly . (b) Before performing a teaching operation, be sure to zero all beams. *…

AHB01ESPP

*2 "Jig P.C.B. Placement Head. Feeder" Group Box

[X1] and [X2] Buttons

Select the [X1] or the [X2] button to specify the head that will

pick up the special jig for teaching operations.

[Fdr. No.] Button

Specify the feeder No. (Fdr. No.) to which the head must be

shifted during the movement to the jig component pick-up po-

sition.

*3 "Select Option" Group Box

The following buttons are provided in this group box.

[All Beam Heads Zero] Button

When this button is pressed, all X/Y beam heads are zeroed.

[Camr. Magnification Teach Start] Button

When this button is pressed, the machine performs a teaching

operation on the magnification of the selected component rec-

ognition camera.

Before performing a teaching operation, pick up the special

jig and zero all beams.

[Jig Component Pickup Position Movement] Button

When this button is pressed, the head moves down to the pick-

up point over the designated feeder and stops.

*4 Set Status

When the "P.E.C. Dsbl." or the "Comp. Recognition Dsbl." check

box in the "Test Run" window is turned on (checked), the background

color of "Recognition Dsbl." turns light red. (No background color in

normal cases).

No recognition processing is made even if a teaching op-

eration is performed when each check box is turned on

(checked) in the "Test Run" window. Therefore, various

teaching operations will get incorrect results.

When "All Beam (Incl. NC Axis) Heads Zero" is completed, the back-

ground color of "All Beam Zero" turns green. (Otherwise, the back-

ground has no color.)

Note

0308-004 6-161

5.7 "Cmpnt Fxd Camr Mag" Tab

AHB01ESPP

(a) When each device is not zeroed and the teaching op-

erations are performed, note that the offset values may

not be taught correctly.

(b) Before performing a teaching operation, be sure to zero

all beams.

*5 Offset Values

Displayed are the current values and the adjusted ones after teach-

ing.

*6 [Vacuum Pick-Up On/Off] Button

When this button is pressed, the vacuum of the selected head is

turned ON or OFF.

*7 Vacuum Pick-Up Mode

Displayed is the vacuum ON/OFF mode of the selected head.

Blue Background : Vacuum OFF

No Background Color : Vacuum ON

*8 [Manual Nozzle Change] Button

When this button is pressed, the "Nozzle Change" sheet appears.

Refer to "4.4 "Nozzle Change" Tab" for details.

*9 [Clear Adj.] Button

When pressed, this button clears the results of the teaching opera-

tion.

*10 [Cancel] Button

When pressed, this button ends the teaching operation without re-

flecting the teaching results on the offset data.

*11 [End] Button

When pressed, this button reflects the results of the teaching op-

eration on the offset data and exits from this session.

*12 "Control Switch" Group Box

Select the items (buttons) to be taught and press the [ON] button

entitled "MOVE". After that, press the [ENABLE] button on the op-

eration panel in 2 seconds. A teaching operation is performed on

the selected item.

Note

0206-002 6-162

5.7 "Cmpnt Fxd Camr Mag" Tab

AHB01ESPP

5.8 "Cmpnt Recog Fxd Camr Ofs" Tab

The corresponding tab sheet enables the operator to perform a teach-

ing operation on the offsets of the component recognition camera (fixed).

When the recognition is performed at the same time, using the P.E.C.

recognition camera and the fixed camera after a jig component is set on

the fixed camera, the deviation from the design position to the fixed cam-

era can be determined.

This teaching operation must be performed only by our service

personnel.

• Sheet Layout

When the "Cmpnt Recog Fxd Camr Ofs" tab is pressed in the "TEACH-

ING" window (submenu), the following tab sheet appears inside the win-

dow.

Fig. 2F113 "Cmpnt Recog Fxd Camr Ofs" Tab Sheet

0206-002 6-163

5.8 "Cmpnt Recog Fxd Camr Ofs" Tab

Note

*10

*11