2OM-1075-002.pdf - 第402页

AHB01ESPP *5 Offset V alues Displayed are the current values and the adjusted ones after teach- ing. *6 [Manual Nozzle Change] Button When this button is pressed, the "Nozzle Change" window appears. Refer to &q…

AHB01ESPP

[X1 Head] and [X2 Head] Buttons

When pressed, the button performs the teaching operation on

the corresponding head (X1 or X2).

Before performing the teaching operation, zero all beams.

*2 [Fdr. No.] Button

When this button is pressed, the "Fdr. No." edit window opens. En-

ter the feeder No. to which the head must be moved, using the ten-

key pad.

*3 "Selection of Teaching Operation" Group Box

The following buttons are provided in this group box.

[All Beam Heads Zero] Button

When this button is pressed, all X/Y beams are zeroed.

[Teach Start] Button

When this button is pressed, a teaching operation is performed

on the selected nozzle.

[Movement to Nozzle Placement Position] Button

When this button is pressed, the head moves to the specified

feeder No. (Fdr. No.) position.

*4 Set Status

When the "P.E.C. Dsbl." or the "Comp. Recognition Dsbl." check

box in the "Test Run" window is turned on (checked), the background

color of "Recognition Dsbl." turns light red. (No background color in

normal cases).

No recognition processing is made even if a teaching op-

eration is performed when each check box is turned on

(checked) in the "Test Run" window. Therefore, various

teaching operations will get incorrect results.

When "All Beam (Incl. NC Axis) Heads Zero" is completed, the back-

ground color of "All Beam Zero" turns green. (Otherwise, the back-

ground has no color.)

(a) When each device is not zeroed and the teaching op-

erations are performed, note that the offset values may

not be taught correctly.

(b) Before performing a teaching operation, be sure to zero

all beams.

Note

0308-003 6-167

Note

5.9 "Head Center Ofs" Tab

AHB01ESPP

*5 Offset Values

Displayed are the current values and the adjusted ones after teach-

ing.

*6 [Manual Nozzle Change] Button

When this button is pressed, the "Nozzle Change" window appears.

Refer to "4.3 "Nozzle Change" Tab" for details.

*7 [Clear Adj.] Button

When pressed, this button clears the results of the teaching opera-

tion.

*8 [Cancel] Button

When pressed, this button ends the teaching operation without re-

flecting the teaching results on the offset data.

*9 [End] Button

When pressed, this button reflects the results of the teaching op-

eration on the offset data and exits from this session.

*10 "Control Switch" Group Box

Select the items (buttons) to be taught and press the [ON] button

entitled "MOVE". After that, press the [ENABLE] button on the op-

eration panel in 2 seconds. A teaching operation is performed on

the selected item.

0308-003 6-168

5.9 "Head Center Ofs" Tab

AHB01ESPP

• Preparation for Teaching Operations

Nozzles

Prepare either [EF01] or [EF02].

Teaching Plate

(Component Recognition Offset Jig: JG-0085)

(Standard Accessory Part)

Handle this fragile jig very carefully.

Fig. 2F115

2 types of patterns are printed through vapor deposition on the glass

for positional calculation.

• Teaching Procedure

(1) Attach the nozzle by hand.

(2) Attach the jig component (the teaching plate (component recogni-

tion offset jig)) to the position where the teaching plate is attached.

The printed side of the component recognition offset jig

should face downward.

(3) Confirm the following.

• The machine is powered.

• The safety doors are completely closed.

(3-1) Press the [Movement to Nozzle Placement Position] button

and bring the head over to the specified feeder No.

(3-2) Press the [Select Nozzle] button in the "Nozzle Change" sheet

to move Nozzle #1 to the "Noz #1" position.

Note

0206-002 6-169

5.9 "Head Center Ofs" Tab