2OM-1075-002.pdf - 第424页

AHB01ESPP *2 "Select Feeder Base" Group Box Select the feeder base to be used for teaching operations. The following buttons are provided in this group box. [Feeder Base 1], [Feeder Base 3], and [Feeder Base 4]…

AHB01ESPP

5.16 "Feeder (A) Ofs" Tab

The corresponding tab enables the operator to perform the teaching

operation on the feeder (A) offset data.

After a master jig is attached to each feeder (Fdr. No.), the offsets of the

master jig can be taught automatically.

This teaching operation must be performed only by our service

personnel.

• Sheet Layout

When the "Feeder (A) Ofs" tab is pressed in the "TEACHING" window

(submenu), the following tab sheet appears inside the window.

Fig. 2F123 "Feeder (A) Ofs" Tab Sheet (Provided with Multi-Layer Tray Feeder 2)

The tab sheet may look different, depending on which options

are selected.

• Sheet Composition

*1 "Select Head" Group Box

The provided buttons make it possible to select the P.E.C. recogni-

tion camera to be used for teaching operations.

The following buttons are provided in this group box.

[X1 Head] and [X2 Head] Buttons

0206-002 6-189

5.16 "Feeder (A) Ofs" Tab

Note

*10

AHB01ESPP

*2 "Select Feeder Base" Group Box

Select the feeder base to be used for teaching operations.

The following buttons are provided in this group box.

[Feeder Base 1], [Feeder Base 3], and [Feeder Base 4] But-

tons

*3 "Select Feeder" Group Box

Select the feeder No. (Fdr. No.) to be used for teaching operations.

*4 Offset Values

Displayed are the current values and the adjusted ones after teach-

ing.

*5 "Selection of Teaching Operation" Group Box

The following buttons are provided in this group box.

[All Beam (Incl. NC Axis) Heads Zero] Button

When this button is pressed, all X/Y beams are zeroed.

[Teach Start] Button

When this button is pressed, a teaching operation is performed

on the selected feeder base.

*6 Set Status

When the "P.E.C. Dsbl." or the "Comp. Recognition Dsbl." check

box in the "Test Run" window is turned on (checked), the background

color of "Recognition Dsbl." turns light red. (No background color in

normal cases).

No recognition processing is made even if a teaching op-

eration is performed when the each check box is turned on

(checked) in the "Test Run" window. Therefore, various

teaching operations will get incorrect results.

When "All Beam (Incl. NC Axis) Heads Zero" is completed, the back-

ground color of "All Beam Zero" turns green. (Otherwise, the back-

ground has no color.)

(a) When each device is not zeroed and the teaching op-

erations are performed, note that the offset values may

not be taught correctly.

(b) Before performing a teaching operation, be sure to zero

all beams.

*7 [Clear Adj.] Button

When pressed, this button clears the results of the teaching opera-

tion.

Note

0206-002 6-190

5.16 "Feeder (A) Ofs" Tab

AHB01ESPP

*8 [Cancel] Button

When pressed, this button ends the teaching operation without re-

flecting the teaching results on the offset data.

*9 [End] Button

When pressed, this button reflects the results of the teaching op-

eration on the offset data and exits from this session.

*10 "Control Switch" Group Box

Select the items (buttons) to be taught and press the [ON] button

entitled "MOVE". After that, press the [ENABLE] button on the op-

eration panel in 2 seconds. A teaching operation is performed on

the selected item.

0206-002 6-191

5.16 "Feeder (A) Ofs" Tab