2OM-1075-002.pdf - 第438页

AHB01ESPP *8 [Clear Adj.] Button When pressed, this button clears the results of the teaching opera- tion. *9 [Cancel] Button When pressed, this button ends the teaching operation without re- flecting the teaching result…

AHB01ESPP

*3 [Fdr. No.] Button and Text Box

When this button is pressed, the "Fdr. No." edit window opens. En-

ter the feeder No. to which the head must be moved, using the ten-

key pad.

*4 "Select Mode (Items to be taught)" Group Box

The following buttons are provided in this group box.

[All Beam Heads Zero] Button

When this button is pressed, all X/Y beams are zeroed.

[Teach Start] Button

When this button is pressed, the machine performs a teaching op-

eration on the selected item.

[Movement to Nozzle Attachment Position] Button

When this button is pressed, the head moves to the specified feeder

No. (Fdr. No.) position.

*5 Offset Values

Displayed are the current values and the adjusted ones after teach-

ing.

*6 Set Status

When the "P.E.C. Dsbl." or the "Comp. Recognition Dsbl." check

box in the "Test Run" tab sheet is turned on (checked), the back-

ground color of "Recognition Dsbl." turns light red. (No background

color in normal cases)

No recognition processing is made even if a teaching op-

eration is performed when the each check box is turned on

(checked) in the "Test Run" tab sheet. Therefore, various

teaching operations will get incorrect results.

When "All Beam (Incl. NC Axis) Heads Zero" is completed, the back-

ground color of "All Beam Zero" turns green. (Otherwise, the back-

ground has no color.)

(a) When each device is not zeroed and the teaching op-

erations are performed, note that the offset values may

not be taught correctly.

(b) Before performing a teaching operation, be sure to zero

all beams.

*7 [Manual Nozzle Change] Button

When this button is pressed, the "Nozzle Change" sheet appears.

Refer to "4.3 "Nozzle Change" Tab" for details.

5.20 "Nozzle Tip Pos Ofs" Tab

Note

0308-004 6-203

AHB01ESPP

*8 [Clear Adj.] Button

When pressed, this button clears the results of the teaching opera-

tion.

*9 [Cancel] Button

When pressed, this button ends the teaching operation without re-

flecting the teaching results on the offset data.

*10 [End] Button

When pressed, this button reflects the results of the teaching op-

eration on the offset data and exits from this session.

*11 "Control Switch" Group Box

Select the items (buttons) to be taught and press the [ON] button

entitled "MOVE". After that, press the [ENABLE] button on the op-

eration panel in 2 seconds. A teaching operation is performed on

the selected item.

5.20 "Nozzle Tip Pos Ofs" Tab

0206-003 6-204

AHB01ESPP

5.21 "Head Master Offset" Tab

The corresponding tab sheet enables the operator to perform a teach-

ing operation on the head master offsets.

This teaching operation must be performed only by our service

personnel.

••

• Sheet Layout

When the "Head Master Offset" tab is pressed in the "TEACHING" win-

dow (submenu), the following tab sheet appears inside the window.

Fig. 2F132 "Head Master Offset" Tab Sheet

••

• Sheet Composition

*1 "Select Head" Group Box

Select the head to be used for teaching operations.

The following buttons are provided in this group box.

[X1 Head] and [X2 Head] Buttons

*2 "Select Nozzle" Group Box

Select the nozzle position to be taught.

*3 Fdr. No.

When this button is pressed, the "Fdr. No." edit window opens. En-

ter the feeder No. to which the head must be moved, using the ten-

key pad.

5.21 "Head Master Offset" Tab

Note

*10

*11

0308-004 6-205