Error Code List.pdf - 第23页

AV131 ERROR CODE LIST 2.3 Er ror Code Table D79EEC- 91-030-A 0 2.3- 6 Error cod e Message 9294 Soft t ask co mm. E rror 9295 So f t c al c ul at io n er r o r 9304 M otion in co mp le te 9305 So ft pa ra mete r e rror 93…

AV131

ERROR CODE LIST

2.3 Error Code Table

D79EEC-91-030-A0

2.3-5

Error code Message

2654

Rear left center safety detection

2655

Rear right center safety detection

2656

Front cover safety detection

2657

Right rail cover safety detection

2658

Left rail cover safety detection

2659

Rear upper cover safety detection

2663

Cancel replacement completion input (open rear left cover)

2664

Cancel replacement completion input (open rear right cover)

2665

Cancel replacement completion input (float left feeder)

2666

Cancel replacement completion input (float right feeder)

2668

Cancel replacement completion input (never open rear left cover)

2669

Cancel replacement completion input (never open rear right cover)

2670

Insertion error (Neither lead detection)

2671

Insertion error (No right lead detection)

2672

Insertion error (No left lead detection)

2673

Anvil short error (left & right lead detection)

2674

Anvil short error (left lead detection)

2675

Anvil short error (right lead detection)

2682

26/52 change error

2696

No PCB on XY table

2697

Feeder type error (26 / 52)

2707

H axis origin off

2708

Feeder float detection error

2710

Safety relay reset condition

2731

PCB carry in restart cancel

2732

PCB carry out restart cancel

2733

PCB sweep out restart cancel

2734

PCB carry start conditional not satisfies

2735

Rail down condition not satisfies

2736

Arm carry condition not satisfies

2737

Arm slowdown condition not satisfies

2738

Rail up condition not satisfies

2739

Arm return condition not satisfies

2748

Emergency stop switch ON safety stop

2756

Axis related error

2757

PCB recognition error (23)

2758

PCB recognition error (16)

2759

PCB recognition error (17)

2760

PCB recognition error (19)

2761

PCB recognition error (45)

2762

PCB recognition error (47)

2763

PCB recognition error (48)

2764

PCB recognition error

2765

PCB recognition error

2766

PCB recognition error

2767

PCB recognition error

4066

This is write protected disk. Please release write protect. Refer to Help for detail.

4067

There is no signature on boot sector. Refer to Help for detail.

9293

Driver soft interlock

AV131

ERROR CODE LIST

2.3 Error Code Table

D79EEC-91-030-A0

2.3-6

Error code Message

9294

Soft task comm. Error

9295

Soft calculation error

9304

Motion incomplete

9305

Soft parameter error

9308

Soft overrun limit

9369

Exclusion process error

9372

Position interrupt error

9373

Complete interrupt error

9400

Axis error

9801

Auto width power on error

9802

Auto width origin return incomplete

9803

Auto width positioning incomplete

9804

Auto width emergency stop input

9805

Auto width command error

9806

Auto width parameter error

9807

Auto width communication error

9809

Auto width origin abnormal

9812

Auto width + overrun error

9813

Auto width - over run error

AV131

ERROR CODE LIST

2.4 Errors

D79EEC-91-210-A0

2.4-1

2.4. Errors

D79EEC-91-210-A0

Emergency switch ON

DESCRIPTION

Emergency switch was detected.

CAUSE

An emergency stop switch was pressed.

SOLUTION

Release the emergency stop switch. (There are five switches. Front; 2 Rear; 3) If the same message appears after

releasing the switch, the switch may be broken. Confirm emergency SW signal in the [Input check] of [Machine

adjustment].

NOTE

Servo switch OFF

DESCRIPTION

Servo switch off

CAUSE

A servo switch is pressed.

SOLUTION

Release the servo switch (1 in front and 1 in back). (KEYLOCK LED of operation panel turns OFF.)

If the same message appears after releasing the switch, the switch may be broken.

NOTE

Air pressure drop

DESCRIPTION

Air pressure drop

CAUSE

Air pressure has dropped.

SOLUTION

When supplied air pressure has dropped, supply air at 0.49MPa - 0.78MPa.

Excessively high setting of the air pressure detector causes an error. Set to 0.4MPa.

Confirm Air pressure (5800H:bit2) in the [input check] of [machine adjustment]. ON: OK, OFF: Drop

NOTE

Cover open stop

DESCRIPTION

Door or cover is open

CAUSE

Safety cover is left open.

SOLUTION

Close the door or cover, then push [return].

Confirm Cover switch (5800H:bit3, 4, 5) in the [input check] of [machine adjustment]. ON: Close, OFF: Open

NOTE

PCB transport error

DESCRIPTION

PCB remains at the transferring part, or PCB is broken.

CAUSE

PCB cannot be transferred properly.

SOLUTION

Check the PCB transfer unit for proper operation.

NOTE