1OM-1625-004_w.pdf - 第137页

1OM-1603 3-14 2. Program Change Operation : Chap.3 1012-005 2.2.4 Preparation for Feeders Procedure (1) Refer to the placement feeder location data in the pattern program and conrm that the required feeders are installe…

1OM-1603

3-13

2. Program Change Operation : Chap.3

1007-004

2.2 Preparation for Program Change Operation

2.2.1 Preparation for Component Library

Library data must be created for new components when there is no component

library data required to create a pattern program.

Reference

(a) Refer to "Chapter 3 Component Library" in Volume 2 for window

navigation.

(b) Refer to "Volume 6: Component Library" for how to create the data.

2.2.2 Creation of Pattern Program for Production Model

A pattern program is required for the automatic operation of the machine.

Reference

Refer to "Chapter 2 Pattern Program" in Volume 2 for details.

2.2.3 Registration of Pattern Program for Production Model

Pattern programs and component library data must be transferred from the

network terminal (option) to the machine.

1OM-1603

3-14

2. Program Change Operation : Chap.3

1012-005

2.2.4 Preparation for Feeders

Procedure

(1) Refer to the placement feeder location data in the pattern program and

conrm that the required feeders are installed.

(2) Replenish each feeder with components.

Reference

Refer to the Instruction Manual for the “Tape Feeder” for SIGMA-G4/G5, for

the component reloading procedure onto a tape feeder.

(3) Install the feeders on the feeder base of the bank feeder change cart.

Note

Before installing the feeders, check which types of feeders should be

installed in which feeder slot Nos. (Fdr. No.).

WARNING

Those who wear implanted pacemakers are not

allowed to handle the tape feeders.

The pacemaker may be affected by the magnetism

and a serious accident will result.

CAUTION

When a tape feeder is attached or detached, be sure

not to drop it.

Otherwise, a foot injury will result or the feeder itself may

be damaged.

Carefully handle each feeder one by one and do not drop

any.

NOTICE

Be sure to install a feeder to the correct feeder slot

(Fdr No.).

Otherwise, some components may be trapped between the

heads.

Be sure to insert the feeder deep inside.

Otherwise, if the suppressor is unhooked or lifted aoat,

it cannot be detected, causing the suppressor to interfere

with a head.

Install the feeders correctly such that they are seated

properly.

Otherwise, they may collide with the head sections or a

pickup error will occur.

1OM-1603

3-15

2. Program Change Operation : Chap.3

1012-004

(4) Attach the bank feeder change cart to the machine.

Reference

(a) Refer to "Attachment and Detachment of Tape Feeders" in the

instruction manual of the tape feeders for how to install the tape

feeders on the bank feeder change cart.

(b) Refer to "3.8 Cart Installation Section" in "Chapter 1" for how to

attach the bank feeder change cart.

CAUTION

Hazardoustoyourhandsandngers!

•

Be sure to hold the handle to move the bank feeder

change cart.

Watch

yourstep!

•

Be careful not to hit your foot against the cart while

moving the bank feeder change cart.

Especially, the resistance against cart movement may

change rapidly when the oor is ragged and the cart

gets caught on the oor or a sheet is used and the cart

gets caught at the edge or a slackened portion of the

sheet.

•

Make sure to insert the feeder into the deep end.

When the tape feeder is mounted onto the feeder

carriage, make sure that it has been inserted into the

deep end and xed securely.

In the case that it has not been xed securely, the tape

feeder might fall, which might cause a lower leg injury

or damage to the feeder..

Feeder Workbench

Bank Feeder Change Cart

Feeder Base

F1C13