00195655-04_SM_X-Series_FSE_en - 第57页
Service Work 3.3.5 Replacing the X Drive (Primary) [03039726- xx] Gantries Service Manual (internal ver sion) SIPLACE HF and X Series 57 3.3.5.1 3 . 3 . 5 . 1 I n s t a lla t io n C h e c k f o r G u id e T r o lle y a n…
Service Work
Gantries 3.3.5 Replacing the X Drive (Primary) [03039726-xx]
56 Service Manual (internal version) SIPLACE HF and X Series
Installation
► Now fit 3 fastening screws on each side. Observe the different screw lengths.
► Remove the lock screws and fit the fastening screws in their place.
► Tighten all fastening screws crosswise with a torque wrench (2.9 N).
► Install the PCB camera.
► Check the gap between the X drive and the magnet cover with a 0.4 mm thickness gauge.
► To do this, place the thickness gauge between the X drive and the magnet cover and then push the
X drive back and forth along the entire length. Make sure none of the parts jam.
Closing drillings for individual head configurations
The drillings used to fasten the head vary between the different head configurations. Those which are
not needed must be closed. This prevents the cooling air from escaping!!
▪ Template for C&P12/6 head [03011690-xx]
▪ Template for C&P20 head [03011694-xx]
▪ Template for TwinHead [03011693-xx]
▪ Grub screws M 4x6-ST [00309422-xx]
► Clean the contact surface of the guide trolley (1) with
a dressing stone (oil stone). Then wipe the contact
surface clean with ethanol.
► Screw the dismantling screws fully into each side of
the new X drive.
► Place the foam rest on the magnetic strip.
► Lift the new X drive up to the guide trolley and fasten
the X drive with the M4x60 lock screws.
► Remove the foam rest.
DANGER!
Risk of fatal injuries through trapped limbs.
Make sure that you do not trap any limbs between the X
drive and the magnetic strip.
1
► Clean all drillings with a pipe cleaner and ethanol, to
remove any adhesive residues.
► Position the relevant template on the centering pins
of the head mount and attach the template.
► Use the holes in the template to screw the grub
screws (with Loctite 241) into the head mount.
► These grub screws must be level with the surface of
the head mount (countersunk).
1
2
Service Work
3.3.5 Replacing the X Drive (Primary) [03039726-xx] Gantries
Service Manual (internal version) SIPLACE HF and X Series 57
3.3.5.1
3.3.5.1 Installation Check for Guide Trolley and Motor Support
Installation Check for Guide Trolley and Motor Support
Installation check
1. Motor plate
2. Guide trolley
3. Distance 0.5 mm
► During installation, place a 0.5 mm feeler gauge be
-
tween the motor plate and the linear guide
. For adjustment purposes, you may need to remove
the X drive and reposition it.
► Check the gap between the X drive and the magnet
cover with a 0.4 mm thickness gauge.
► To do this, place the thickness gauge between the X
drive and the magnet cover and then push the X drive
back and forth along the entire length. Make sure
none of the parts jam.
Service Work
Gantries 3.3.6 Replacing the X Axis Incremental Encoder
58 Service Manual (internal version) SIPLACE HF and X Series
3.3.6
3.3.6 Replacing the X Axis Incremental Encoder
Replacing the X Axis Incremental Encoder
Please also observe the technical information "Overview of Scales and Read Heads" [DE: TI2014-
05D11] [EN: TI2014-05E11].
Parts, Equipment and Tools
▪ Read head MS22.74 X/Y 677mm [03090201-xx] (replaces: [03020588-xx])
Overview
Press-fit connections
NOTICE
Head interface
The new read head for the X axis "Read head MS22.74 X/Y 677 mm [03090201-xx] may only
be fitted with a "head interface" from FS06 [03000901-06] or a "mirrored head interface" from
FS03 [03029048-03].
The read head can only be fitted together with the new "Tape measure X axis SX4" [03092558-
xx]. If an old read head is upgraded to the new version MS22, you will also need to replace the
scale.
1. Installation point for head interface and Vision board
2. Incremental encoder position
► Unplug the incremental encoder press-fit connection
(2) from the head interface (1).
1
2
Assembly Gantry Board Connectors
X axis incremental en
-
coder
Gantry 1 (C&P head ) Head interface
[03000901
-
xx]
X15ac
X axis incremental en
-
coder
Gantry 2 (TwinHead) Head interface
[03000901
-
xx]
X15bc