00195655-04_SM_X-Series_FSE_en - 第87页
Service Work 3.5.2 Settings the C&P20 (FSE) Jaws C&P20 Placement Head Service Manual (internal ver sion) SIPLACE HF and X Series 87 3.5.2 3 . 5 . 2 S e t t in g s t h e C & P 2 0 ( F S E ) J a w s Settings th…
Service Work
C&P20 Placement Head 3.5.1 Replacing the E/D Transformer (Collector Ring) - FSE
86 Service Manual (internal version) SIPLACE HF and X Series
Removing the E/D transformer
► The upper side of the E/D transformer (2) has a service opening (1), through which you can loosen
the 5 fastening screws. Simply turn the upper section over the individual screws and loosen these in
succession.
► Attention:
Do not loosen the index screw (4).
► Carefully pull the E/D transformer (2) upwards and out of the connection (6) on the star (5).
⇨ The star has an index screw (4), which enables you to fit the E/D transformer in the correct posi
-
tion.
► Fit the E/D transformer (2) so that the index screw is aligned with the groove in the E/D transformer.
⇨ Make sure that the connector (6) engages correctly.
► Fix the E/D transformer with the 5 fastening screws, through the service opening (1).
Fitting the E/D transformer
1. Service opening
2. E/D transformer
3. Groove for index screw
4. Index screw
5. Star
6. Connectors
6
1
5
4
3
2
► Turn the E/D transformer (2) so that the index screw
(4) is aligned above the groove (3) in the E/D trans
-
former.
► Fit the star with E/D transformer (5) carefully with the
pins on the motor shaft into the star carrier.
► Attach the connection cable to the E/D transformer
(2).
► Fit all the components you removed. Follow the in
-
structions in the relevant sections of this service man
-
ual.
1
5
4
3
2
Service Work
3.5.2 Settings the C&P20 (FSE) Jaws C&P20 Placement Head
Service Manual (internal version) SIPLACE HF and X Series 87
3.5.2
3.5.2 Settings the C&P20 (FSE) Jaws
Settings the C&P20 (FSE) Jaws
3.5.2.1
3.5.2.1 General
General
Contents of service kit for setting C&P20 jaws [03058847-01]:
▪ Jaw setting gauge with 2x hexagon socket-head screw M2.5x12 mm [03045455-01]
▪ 4 x feeler gauge 0.01 mm [03058840-01]
▪ Feeler gauge 0.04 mm [03058839-01]
▪ Hose piece D12 length 20 mm [03058392-01]
▪ Rubber hose to protect the component sensor
▪ 10x dead indexing plate [03013091-01]
Tools required:
▪ Phillips screwdriver with torque limiter, set to 35 Ncm
▪ Head mounting rack
▪ Hexagon socket-head wrench
NOTICE
SIPLACE Service
This setting may only be performed by the SIPLACE service team!
Jaw setting gauge
1. Side stop for jaws
2. 2a and 2b: contact surfaces for jaws
3. Centering pins for accurate setting to raceway
4. Gauge fixture on raceway (screws --> M2.5x12 mm)
Service Work
C&P20 Placement Head 3.5.2 Settings the C&P20 (FSE) Jaws
88 Service Manual (internal version) SIPLACE HF and X Series
3.5.2.2
3.5.2.2 Basics
Basics
The jaws need to be correctly set, to ensure that the bridge between the raceway and jaws is accurate.
The correct height between the raceway and jaws is achieved by determining the zero point correction
value for the Z axis.
When fitting the jaws at the Z axis, you can rotate the jaws. Use the setting gauge to set the correct angle
of the jaws to the raceway.
When do you need to set the jaws?
▪ When replacing the light barrier down, check the position of the jaws (in SITEST).
▪ When fitting the new Z axis drive.
▪ When error messages are issued by the station software (e.g. reference run).
Raceway with Z axis
1. Raceway
2. Ball bearing on segment
3. Snap jaws
4. Light barrier down
5. Bridge raceway – jaws, left
6. Bridge raceway – jaws, right