00195166-0402_SM_D4_EN - 第152页

Service Work C&P12 Placement Head Replacing the Co mponent Camer a (D Series) [03014449 -xx] 152 Serv ice Manual SIPLACE D4 Installation See also: J 6.3.1 Calibrating the C&P Head and Cameras [ J  221] X Make su…

Service Work

Replacing the Component Camera (D Series) [03014449-xx] C&P12 Placement Head

Service Manual SIPLACE D4

151

4.5.3 Replacing the Component Camera (D Series) [03014449-xx]

Removal/Installation

The component camera must be replaced as a

complete unit. This consists of the lens system,

camera, amplifier, illumination planes and

"illumination controller" board.

Article numbers

 SST28 [03014449-xx]

 SST29 [03018637-xx]

NOTE:

You may need to completely dismantle

the front part of the head (4), so that the

components can be more easily

accessed.

ATTENTION: Do not damage the

fixture clips!

To disconnect the component and PCB

camera connections, you need to open

the fixture clips by applying pressure to

the side of the connector.

X For details see section (4.5.22 Press

Fit Connections with Fixture Clips on

the Vision Board (D Series)

J

196 )

X Disconnect the flat ribbon cable holders (5) at

the Vision board (7) of the gantry head

distributor.

X Pull both flat ribbon cable connectors (6) off

the Vision board of the gantry head

distributor (2).

X Loosen the four screws (3) holding the

component camera.

X Carefully lift off the component camera (1).

Service Work

C&P12 Placement Head Replacing the Component Camera (D Series) [03014449-xx]

152 Service Manual SIPLACE D4

Installation

See also:

6.3.1 Calibrating the C&P Head and Cameras [

J

221]

X Make sure that all contact surfaces are clean.

X Place the holes in the camera on the parallel

pins (4).

X Carefully position the camera on the C&P

head, until the camera plinth lies flat on the

contact surface of the front part of the C&P

head.

X Fix the camera in place with the four screws

provided (3).

X Fit the front part of the C&P head (4).

X Reconnect the flat ribbon cables (6) to the

Vision board (7) of the gantry head distributor.

X Refit the flat ribbon cable strain relief (5). This

reestablishes the ground connection.

X Start the machine.

X Use the SITEST program to calibrate the C&P

head.

Service Work

Replacing the Intermediate Distributor [00330648] C&P12 Placement Head

Service Manual SIPLACE D4

153

4.5.4 Replacing the Intermediate Distributor [00330648]

Removal/Installation

The following supply voltages and signals are routed by the intermediate distributor to the individual

placement head modules or to the head board:

X Please observe the ESD regulations for the

following work and use an ESD ground strap.

X Loosen the four fastening screws and remove

the cover (1), by pulling these off the 4 snap

fasteners.

X Undo the four spacer bolts (3) and tilt the

intermediate distributor (2) a little.

4-41: Position of the sockets

Legend

1. Front of the intermediate distributor

2. Back of the intermediate distributor

 U4 = pressure sensor

X Carefully disconnect the hose from the

pressure sensor (U4).

X Disconnect the connection plugs from their

slots. Refer to the circuit diagram folder for the

relevant machine.

X Remove the intermediate distributor.

X Restore connections X1......X12.

X Push the hose onto the pressure sensor tube

(U4).

X Fasten the intermediate distributor.

NOTE:

X No settings are required.

X The axis machine data can be rewritten in the memory of this board via the SITEST menu

Replace head