00195166-0402_SM_D4_EN - 第185页
Service W ork Replacing the Star [00341181] C&P12 P lacement Head Service Manual SIPLACE D4 185 Installation X Installation is perform ed by following the abov e instruction s in the reve rse order . Observe th e fol…
Service Work
C&P12 Placement Head Replacing the Star [00341181]
184 Service Manual SIPLACE D4
4.5.17.2 Replacing the Air Blast Supply to the Star [03000896-xx]
Removal/Installation
4.5.17.3 Replacing the Silicone Hoses on the Star [00341183S01]
Removal
NOTE: Do not remove the star!
For clarity, the diagram shows the star
when removed from the machine.
However, you do not need to remove
the star to replace the air blast supply.
X Undo and remove the two screws fastening
the air blast supply (1).
X Fasten the air blast supply with the two screws
provided.
X Dismantle the star from the C&P head.
X Remove the sleeve from the segment of the
defective hose.
X Undo and remove the two screws fastening
the air blast supply (1).
X Disconnect the hose (3) from the segment (1).
X Now pull the valve (2) out of the star.
ATTENTION: O-ring
There is an O ring behind the valve.
Make sure that you do not lose this and
that you fit it again during installation!
X Disconnect the hose from the valve.
Service Work
Replacing the Star [00341181] C&P12 Placement Head
Service Manual SIPLACE D4
185
Installation
X Installation is performed by following the above instructions in the reverse order. Observe the
following points:
Check that the white connection pieces are seated firmly on the segments. If these are loose, you
will need to replace the entire star.
Make sure that there is an even space between the hoses:
When fitting the star, make sure that the silicone hoses are not pinched and/or damaged.
ATTENTION:
If the connecting silicone hoses
between the valve and segment are
replaced, make sure that they are not
damaged by rubbing against one
another (2) .
X To ensure this, make sure that the
silicone hoses have been cut to the
exact length and that they are
pushed onto the respective
connection pieces as far as possible
(up to the stopper).
X Make sure that the hoses do not
touch (1) one another. Check the
distance while pushing all segments
all the way in. Ideally, the distances
should all be the same.
Service Work
C&P12 Placement Head Replacing the Star Drive [03020626-xx]
186 Service Manual SIPLACE D4
4.5.18 Replacing the Star Drive [03020626-xx]
Removal
Installation
See also:
J
6.3.9 Determining the Zero Point Correction for the Star Axis of the C&P Head [
J
230]
Legend
1. Star drive, digital / DLM3
2. 4 x M5x16 hexagon socket-head screws
3. Front section of C&P head
(A) Connecting cable for the star drive
X Dismantle the intermediate distributor.
X Dismantle the front part of the C&P head.
X Dismantle the star.
X Loosen the four M5x16 hexagon socket-head
screws (2).
X Lift the star drive off the front part of the C&P
head.
A
1
3
2
X Place the star motor onto the front part of the
C&P head, so that the star drive connection
cable points to the position marked (A).
X Fix the star drive in place with the four M5x16
hexagon socket-head screws (2).
X Fit and adjust the star. (See zero point
correction.)
X If you are unable to adjust the zero point
correction correctly, loosen the 4 star motor
screws and rotate the star motor in the
required direction, within the tightening
tolerance.
X Fit the front part of the C&P head.
A
1
3
2