00195166-0402_SM_D4_EN - 第221页

Settings Calibrating the C&P Head and Cameras C&P12 Service Manual SIPLACE D4 221 6.3 C&P12 6.3.1 Calibrating the C&P Head and Cameras Automatic calibration of all heads and cam eras 6-8: The menu may var…

Settings

Gantry Checking the DIP Switches

220 Service Manual SIPLACE D4

6.2.4 Checking the DIP Switches

6.2.4.1 DIP Switch on Gantry Head Distributor

* Not all gantries may be available, depending on the machine type.

6.2.4.2 DIP Switch on Vision Board

* Not all gantries may be available, depending on the machine type.

6.2.5 Mechanical Adjustment of the Incremental Encoder

The incremental encoders (read units) on the X and Y axis are adjusted exactly to the position of the

incremental scale. The two limit marks on the incremental encoder show where the top/bottom positions

of the scale should be. The encoder is also mechanically set to a distance of 0.4 mm +/- 0.1 mm to the

incremental scale.

After this adjustment of the incremental encoder you have to check the zero pulse and track signals.

Correct installation should ensure correct count and zero pulse signals. For troubleshooting purposes

(error analysis and fixing), you will need to measures these signals with the oscilloscope. (See service

manual.)

S Setting for gantry* Comments

1 2 3 4

1 OFF ON OFF ON P0 – gantry ID0 address switch 1 --> gantry

2OFF OFF ON ONP1 – gantry ID1 address switch 2 --> gantry

3 OFF OFF OFF OFF S1 – switch for DLM head (delay switching on

LB down – Z-axis)

4 OFF OFF OFF OFF BL – Enable boot loader for serial port

5 OFF OFF OFF OFF Reset - CAN processor 16 Bit (TQM module)

6 OFF OFF OFF OFF C0 – no current function

7 OFF OFF OFF OFF C1 – no current function

8 OFF OFF OFF OFF S2 – switch for DLM head (no current function)

S Setting for gantry* Comments

1 2 3 4

1 OFF OFF OFF OFF Boot mode - CAN processor 16 Bit via

connector X11

2 OFF OFF OFF OFF Reset - CAN processor 16 Bit to subboard

3 OFF ON OFF ON P0 - Address switch 1 --> Gantry

4OFF OFF ON ONP1 - Gantry address switch 2

5 OFF OFF OFF OFF WPE - Write protect enable, currently OFF

6 OFF OFF OFF OFF CAN R - Switch terminator CAN bus

7ONONONONTest 1 - CAN 1 MBit/s --> ON

8ONONONONTest 0 - CAN IDs --> ON

NOTE:

To set this distance, use one or more small plastic disks with a total thickness of 0.4 mm.

Settings

Calibrating the C&P Head and Cameras C&P12

Service Manual SIPLACE D4

221

6.3 C&P12

6.3.1 Calibrating the C&P Head and Cameras

Automatic calibration of all heads and cameras

6-8: The menu may vary, according to the machine type and configuration.

X In the SITEST menu, select

Calibrate Entire

Machine

-->

All Heads and Cameras

to open

the adjacent menu.

X In

Job Selection

(1) , select the components

to be calibrated.

NOTE:

These two entries (2) are optional.

X To continue calibration with manual handling,

select the four consecutive menus in Section

Positions

(1) and the two menu items in the

Section

Mapping

(2).

Settings

C&P12 Boards at C&P12

222 Service Manual SIPLACE D4

6.3.2 Boards at C&P12

All the settings described in this chapter are head-specific and apply here for the C&P12.

6.3.2.1 8-fold DIP Switch of the gantry head distributor (incl. switch S1) – C&P6/12

Switch P0 and P1:

Switch S1:

 ON – Test mode (without delay)

 OFF – Default state (with delay of 3.6 ms+/- 300 us) means: Z axis moves downwards, the top LB is

released and the LB down is enabled after a delay of 3.6 ms.