KE-2070_2080_InstructionManual_C_Rev01.pdf - 第7页

KE-2070/2080 使用说明书目录 Rev01 i 目录 · 为了安全使用机器第 1 部基本编第 1 章设备概要 1-1 本设备的概要 ······························ 1-1 1-1-1 前言 ································ 1-1 1-1-2 特点 ································ 1-2 1-1-3 系统构造 ······…

为了安全使用 KE-2070/80 的注意事项

1.为了防止触电引起的事故，请勿在接通电源的状态下打开电气设备箱。

2.为防止触电，请勿在拆下接地线的状态下运行。

1.为防止人身受伤，请勿在拆下安全罩、安全装置等状态下运行。

2.为防止人身受伤，请务必小心，以免头发、衣服等被卷入传送带链。此外，请勿戴手套。

3.为防止人身受伤，维护时（加油、调试、日常检修），请切断电源。

4.为防止人身受伤，请在电源线上使用漏电断路器。

1.本装置的操作系统采用 Windows XP（包括以太网通信功能）。

除安装本装置提供的软件之外，加装其他软件，不保证正常运行。对 HDD 内组装的文件

进行转移、重命名、文件夹·文件的压缩、复制，也同样不保证正常运行，敬请谅解。

● 万一出现此钟情况，需要更换新的 SSD 或 HDD，有可能丢失数据，务请格外注意。

为保护操作系统，使用了 Enhanced Write Filter(EWF)组件，进行了 C 盘 ROM 化。

1.请不要在 C 盘保存文件。

把文件保存在 ROM 化后的 C 盘，会仿真占用主存储器。因而，把文件存在 C 盘里时，会

增加主存储器的使用量，压迫系统。反复保存后可能造成内存不足，显示系统错误，可

能需要重启本设备。

2.需要修改 OS 信息时，必须刷新 C 盘操作。操作方法请参见使用说明书「1－5 更新C盘的

操作」。

需要修改 OS 信息的操作是指下列事项：

·KE-2070/80 系统软件、Flex Line DB 的版本升级

·触摸屏自我校正

·添加打印机

·设置网络（IP 地址、工作组等）

·变更日期和时间

·添加用户

·变更资源管理器的设置

·变更 UPS 实用程序（UPSilon2000）的设置

●要变更操作系统信息时，在修改 C 盘操作后，需要重启一次本装置。

1.本装置配备有 UPS，以保护停电时的生产程序等。

为防止 UPS 内置电池劣化，请勿在非通电状态下将本装置放置 6 个月以上。

●本装置以电流总断路器及总开关 ON 的状态为通电状态。

〈安全盖〉

1．开关安全盖时请注意下列事项。

• 打开安全盖时要把盖子向上开足直到上了锁，确认上了锁后再放开手。

没有上好锁就放开手时，盖子有落下来的危险。

• 关盖子时先解开锁，再关闭盖子。

（请注意，解开锁时不要使盖子落下来导致受伤。）

• 不要过渡增加盖子、手把等的负荷。

1. 安装等时请不要站到机器上面，以免损坏外罩类。

注意

危险

注意

KE-2070/2080 使用说明书目录 Rev01

·为了安全使用机器

第 1 部基本编

第 1 章设备概要

1-1 本设备的概要······························ 1-1

1-1-1 前言 ································ 1-1

1-1-2 特点 ································ 1-2

1-1-3 系统构造 ······························ 1-4

1-2 本设备的构成······························ 1-6

1-2-1 本设备的构成 ···························· 1-6

1-2-1-1 基板传送部分的构造 ···················· 1-8

1-2-1-2 元件供给部分的构成 ···················· 1-9

1-2-1-3 贴片头单元的构成 ···················· 1-10

1-2-1-4 ATC 单元（Auto Tool Changer 自动工具交换装置）的构成 ·· 1-11

1-2-1-5 吸嘴 ·························· 1-12

1-2-1-6 OCC 的构成 ······················ 1-14

1-2-1-7 VCS 的构造 ······················ 1-15

1-2-1-8 HMS ························· 1-16

1-2-2 机器规格 ····························· 1-17

1-2-3 电气规格 ····························· 1-20

1-2-4 对象元件及元件包装方式 ······················ 1-21

1-2-5 基板规格 ····························· 1-29

1-2-6 定心系统 ····························· 1-33

1-2-7 X,Y,Z,θ轴的说明·························· 1-38

1-2-8 与外部设备的接口 ························· 1-39

1-2-9 略语说明 ····························· 1-42

1-3 基本操作································ 1-43

1-3-1 画面的构成 ···························· 1-43

1-3-2 输入装置 ····························· 1-45

1-3-3 操作方法 ····························· 1-51

1-4 菜单与命令······························· 1-58

1-5 文件·································· 1-

1-5-1 新建 ······························· 1-72

1-5-2 打开(文件的读入) ························· 1-72

1-5-3 保存 ······························· 1-73

KE-2070/2080 使用说明书目录 Rev01

1-5-4 另存为 ······························ 1-73

1-5-5 文件管理 ····························· 1-75

1-5-6 生产程序初始文件夹 ························ 1-76

1-5-7 打印机设置 ···························· 1-76

1-5-8 打印 ······························· 1-77

1-5-9 设备信息的保存 FD ························· 1-79

1-5-10 保存图像数据 FD ·························· 1-80

1-5-11 硬件安全拆卸 ··························· 1-81

1-6 C 盘的更新操作 ····························· 1-82

第 2 章生产

2-1 流程图································· 2-1

2-2 概要·································· 2-2

2-2-1 生产模式 ······························ 2-2

2-2-2 生产流程 ······························ 2-3

2-2-3 生产主菜单的构成 ·························· 2-4

2-3 装置的启动和退出···························· 2-6

2-3-1 装置的启动 ····························· 2-6

2-3-2 装置的结束方法 ··························· 2-9

2-3-3 停电时的措施 ··························· 2-10

2-3-4 接通电源时吸嘴安装异常 ······················ 2-14

2-3-5 事件画面 ····························· 2-17

2-4 预热·································· 2-18

2-4-1 初始画面 ····························· 2-18

2-4-2 条件设置 ····························· 2-18

2-4-3 运行内容 ····························· 2-20

2-5 空运行模式······························· 2-21

2-6 文件操作································ 2-22

2-6-1 打开(读入文件) ·························· 2-22

2-6-2 保存 ······························· 2-23

2-6-3 另存为 ······························ 2-23

2-7 生产准备································ 2-24

2-7-1 基板的设置 ···························· 2-24

2-7-1-1 传送部的构成 ······················ 2-25

2-7-1-2 传送轨道宽度的调整 ··················· 2-26

2-7-1-3 销基准的调整方法 ···················· 2-28

2-7-1-4 外形基准的调整方法 ··················· 2-31

2-7-1-5 其他调整 ························ 2-34