00195376-05_SM_D1_D1i_D2_D2i_EN - 第137页

Service Work 4.4.11 Replacing the Z Axis Drive C&P6/12 Head Service Manual SIPLACE D1/D1i/D2/D2i 137 See also   6.5.6 Setting the Z axis Belt Tension [ ➙ 235] ► Tighten the two M3x14 hexagon socket-head screws (6) …

100%1 / 280
Service Work
C&P6/12 Head 4.4.11 Replacing the Z Axis Drive
136 Service Manual SIPLACE D1/D1i/D2/D2i
4.4.11
4.4.11 Replacing the Z Axis Drive
Replacing the Z Axis Drive
Parts, equipment and tools
▪ Z motor with interference suppression board DLM1, DLM2, DLM3 [03038908-xx]
▪ Z motor with interference suppression board DLM4 [03083864-xx]
Removal
Installation
1. 4 x M3x5 hexagon socket-head screws with locking
varnish
2. Z axis drive
3. 2 x M2.5x12 hexagon socket-head screws
4. Motor clamp upper part /DLM3
5. Motor clamp/DLM3 (do not confuse this with the as-
sembly clamp for the Z motor tacho interference sup-
pression board)
6. 2 x M3x14 hexagon socket-head screws
7. Toothed belt
► Switch off the machine and secure it to prevent unau-
thorized reactivation.
► Remove the plugs (motor tacho and incremental en-
coder) from the sockets on the intermediate distribu-
tor.
► Loosen the four M3x5 hexagon socket-head screws
which have been fixed with locking varnish (1).
► First loosen the upper M2.5x12 hexagon socket-head
screw (3) of the motor clamp fitting 2 (4), then the low-
er one.
► Loosen the two M3x14 hexagon socket-head screws
(6) on the motor clamp fitting (5).
► Carefully remove the Z axis drive (2) together with the
cables.
► Insert the Z axis drive (2).
► Make sure that the teeth of the toothed belt (7) en-
gage in the teeth of the motor pinion (1).
► Use the four M3x5 hexagon socket-head screws to fit
the Z axis drive.
► Tension the Z axis toothed belt by moving the Z axis
drive unit upwards and fix the motor with at least one
screw.
► Check the toothed belt tension with the belt tension
measuring device.
Frequency in Hz Before continuous opera-
tion run
After continuous operation
run
Toothed belt T2 / DLM3 on the Z axis 280 +/- 10 280 +/- 10
Service Work
4.4.11 Replacing the Z Axis Drive C&P6/12 Head
Service Manual SIPLACE D1/D1i/D2/D2i 137
See also
6.5.6 Setting the Z axis Belt Tension [ ➙ 235]
► Tighten the two M3x14 hexagon socket-head screws
(6) to fix the motor clamp (5).
► Fix the motor clamp upper part (4) with the two
M2.5x12 hexagon socket-head screws (3).
► Now tighten the hexagon socket-head screws on the
Z axis drive unit and the motor clamp.
► Check the Z axis top stop with the setting gauge.
Service Work
C&P6/12 Head 4.4.12 Replacing the Z Axis Toothed Belt [00334936-xx]
138 Service Manual SIPLACE D1/D1i/D2/D2i
4.4.12
4.4.12 Replacing the Z Axis Toothed Belt [00334936-xx]
Replacing the Z Axis Toothed Belt [00334936-xx]
Removal
Installation
1. Z axis drive
2. Z axis toothed belt
3. 2 x deflection wheel / DLM3
4. Tension jack (Z axis clamping device)
► Switch off the machine and secure it to prevent unau-
thorized reactivation.
► Loosen the two screws fastening the tension jack (3).
► Loosen the two M2.5x12 hexagon socket-head
screws (3) on the motor clamp fitting (4).
► Loosen the two M3x14 hexagon socket-head screws
(6) on the motor clamp fitting (5).
► Slightly loosen the four M3x5 hexagon socket-head
screws (1).
► Remove the toothed belt (7).
► Place the new toothed belt over the pinion of the Z
axis drive and the deflection wheels.
NOTICE!
Make sure that the teeth of the toothed belts engage in
the teeth of the pinion and deflection pulleys.
► Fit the tension jack (4) with the two fastening screws,
to the toothed belt.