00195376-05_SM_D1_D1i_D2_D2i_EN - 第159页
Service Work 4.4.25 Replacing the Vacuum Hoses on the C&P Head C&P6/12 Head Service Manual SIPLACE D1/D1i/D2/D2i 159 Removal/installation ► Mark the connection points a nd the route of the individual hose s, so t…
Service Work
C&P6/12 Head 4.4.24 Replacing the Membrane (Vacuum Plate) on the Sleeve [03037984-xx]
158 Service Manual SIPLACE D1/D1i/D2/D2i
4.4.24
4.4.24 Replacing the Membrane (Vacuum Plate) on the Sleeve [03037984-xx]
Replacing the Membrane (Vacuum Plate) on the Sleeve [03037984-xx]
The sealing membrane on the sleeves ensures sufficient vacuum by sealing the tip of the nozzle (serves
as the air inlet) in the sleeve.
Tools and equipment
▪ Standard tool
▪ Spare part: membrane (vacuum plate) [03037984-xx]
Removal
► Loosen the old membrane with an Allen key (1.5 mm) and remove the membrane.
Installation
► Fit the new membrane onto the sleeve and tighten the membrane with an Allen key.
4.4.25
4.4.25 Replacing the Vacuum Hoses on the C&P Head
Replacing the Vacuum Hoses on the C&P Head
The length of the vacuum hoses and the way in which they are fitted has been improved to ensure that,
when the hoses are replaced - especially in SX, DX, X, D3 and HF machines - these hoses can be run
in a manner which will not interrupt the vacuum supply.
Tools and equipment
▪ Standard tool
▪ Spare part: vacuum hoses and guidance [03064147-xx]
Contents:
– Hose for placement circuit query (new length: 180 mm, old length: 190 mm) [03002187-02]
– Hose for holding circuit query (new length: 225 mm, old length: 200 mm) [03002188-02]
– Hose for placement circuit / 3x6x145 (new length: 145 mm, old length: 125 mm) [03010444-02]
– Hose for hold circuit / 4x7x140 [03010445S01]
– Hose guide [03048807-01]
– Cylinder screw M3x6 DIN912-A2 [03045028-01]
Blue membrane for the sleeve with ball fixing C&P6/12
(old version [00354244-xx])
White membrane for the sleeve with ball fixing C&P6/12,
made of an alternative material
(new version [03037984-xx])
CAUTION
Do not use a ball Allen key!
► Make sure that you do not use a ball Allen key.
Service Work
4.4.25 Replacing the Vacuum Hoses on the C&P Head C&P6/12 Head
Service Manual SIPLACE D1/D1i/D2/D2i 159
Removal/installation
► Mark the connection points and the route of the individual hoses, so that these can be rerun correctly
later on.
► Disconnect the hoses from the vacuum generator and the vacuum measuring board.
► Fit the additional hose guide (M3 screw) on the top measuring hose duct.
► Fit the new hose as shown in the diagrams.
Service Work
Pick&Place Head 4.5.1 Replacing the Pick&Place Head [03033628-xx]
160 Service Manual SIPLACE D1/D1i/D2/D2i
4.5
4.5 Pick&Place Head
Pick&Place Head
4.5.1
4.5.1 Replacing the Pick&Place Head [03033628-xx]
Replacing the Pick&Place Head [03033628-xx]
Overview
► Move the component trolley out of the machine.
► Switch off the machine.
► Move the P&P head to a suitable working position.
► Detach the compressed air connection from the P&P head to the vacuum distributor (1).
► Unplug the flat ribbon cable from the main board (2) on the P&P head.
The P&P head is fixed with 4 screws to the head mount (3) and is positioned with two pins.