00195376-05_SM_D1_D1i_D2_D2i_EN - 第187页
Service Work 4.8.4 Replacing the Solenoid Valve s [03000630] Cutter Service Manual SIPLACE D1/D1i/D2/D2i 187 4.8.4 4 . 8 . 4 R e p la c in g t h e S o le n o id V a lv e s [ 0 3 0 0 0 6 3 0 ] Replacing the Sole noid Valv…
Service Work
Cutter 4.8.3 Replacing the Control Unit [03006411]
186 Service Manual SIPLACE D1/D1i/D2/D2i
Installation
4.8.3
4.8.3 Replacing the Control Unit [03006411]
Replacing the Control Unit [03006411]
Removal/Installation
► Install the proximity switch (1) precisely in the position
you marked with the permanent marker.
► Insert the prepared cylinder into the cutter, with the
correct rotary position of the articulated joint (2) i.e.
the joint axes must be vertical.
► Fasten the cylinder in this position, with the 2 screws
provided (3).
► Connect the compressed air hoses to the cylinder in
the correct allocation.
► Check the gap between the leading edge of the tape
deflector and the "empty-tape baffle, inside".
► Check the switching points of the proximity switches.
1
3
2
NOTICE
If the tapes are not cut correctly, even though the switching points have been set properly and
the short-stroke cylinder has been exchanged - complete with the one-way restrictor - the cause
of the problem may be:
► Incorrect compressed air level
► Leaking compressed air connection or Y-socket union
Legend
1. Control unit under the cover
► Dismantle the waste slide.
► Remove the cover (1) from the control unit.
1
Service Work
4.8.4 Replacing the Solenoid Valves [03000630] Cutter
Service Manual SIPLACE D1/D1i/D2/D2i 187
4.8.4
4.8.4 Replacing the Solenoid Valves [03000630]
Replacing the Solenoid Valves [03000630]
Overview
► Mark the allocation of all press-fit connections and
disconnect all press-fit connections (2) from the con-
trol unit.
► Remove the cable ties and the connection cable fix-
tures.
► Carefully pull the control unit (3) off its mount (4).
► Carefully insert the new control unit onto the mount,
in the correct rotary position and location, until it locks
into place.
► Restore all plug-and socket connections in the cor-
rect allocation.
► Run the connection cables and fasten with cable ties
(strain relief).
► Check the jumper setting according to the label on
the control unit and adjust, if necessary.
► Replace the control unit cover.
► Fit the waste slide.
1
4
3
2
1. Position of the solenoid valves
1
Service Work
Cutter 4.8.5 Replacing the Proximity Switch [00332894]
188 Service Manual SIPLACE D1/D1i/D2/D2i
Removal/Installation
4.8.5
4.8.5 Replacing the Proximity Switch [00332894]
Replacing the Proximity Switch [00332894]
Overview
Removal/Installation
Legend
1. Solenoid valve assembly
► Loosen the compressed air connections (3) on the
solenoid valve.
► Unplug the press-fit connection (2) on the solenoid
valve connection cable.
► Loosen the screws (4) holding the solenoid valve in
place and remove the solenoid valve.
► Fit the new solenoid valve and establish the press-fit
connection to the valve.
Attach cable ties (strain relief) where necessary.
1
4
3
2
Legend
1. 2 proximity switches on each short-stroke cylinder
1
► Use a permanent marker to mark the exact installa-
tion position (3) of the proximity switch (1) or (2) on
the short-stroke cylinder.
► Loosen the screw fastening the proximity switch to
the short-stroke cylinder.
► Unthread the connection cable to the control unit.
► Install the proximity switch precisely in the position (3)
you marked with the permanent marker on the short-
stroke cylinder.
► Secure the fastening screws with locking varnish.
► Reconnect to the electricity supply.
► Check the switching points of the proximity switches.
1
2
3
3