80S-2080F480F4-680F5 User’s Manual - 第399页
6 What should you do ... ? SIPLACE 80S-20/F4/F4-6/F5 User’s Manual 6.3 When you change the job Edition 03/98 from Software Version S R.404.xx 6 - 8 6.3 When you change the job Stop the p lacement program at the line c om…
SIPLACE 80S-20/F4/F4-6/F5 User’s Manual 6 What should you do ... ?
Edition 03/98 from Software Version SR.404.xx 6.2 When you switch off the SIPLACE line
6 - 7
6.2.2 Switching off the stations
ATTENTION
When an automatic placement system is in use, NEVER just power it off at the main switch (apart from in an emer-
gency).
The station computer runs under the WINDOWS NT operating system. You must shut down the operating
system correctly before switching off the station. The procedure for switching off the station is as follows:
End all placement and gluing operations.
Check that the z axes of all placement and glue application heads are in their top end position.
Check whether there are still components on the placement heads.
Move all gantries into the standby position.
Click on the ’Shut down computer’ option in the ’Operation’ menu.
This will end all the processes running on the station computer. A prompt will then appear on screen, tell-
ing you that you can safely switch off the computer.
You can now switch off the placement system at the main switch.
PLEASE NOTE:
If you switch off the placement system while it is in use without first correctly shutting down the station com-
puter, the computer might not start again the next time you start up the line.
6 What should you do ... ? SIPLACE 80S-20/F4/F4-6/F5 User’s Manual
6.3 When you change the job Edition 03/98 from Software Version SR.404.xx
6 - 8
6.3 When you change the job
Stop the placement program at the line computer (job control: red lamp).
Specify the new placement program.
Check the width of the conveyor belt.
Check the position of the magnetic supports and make sure that they cannot collide with components on
the bottom of the PCB.
Carry out the set-up check.
Check that the feeder modules are equipped with the correct components and that they are at the correct
locations.
Check the nozzle configuration.
If no nozzle changer is installed, you must change the nozzles manually.
PLEASE NOTE:
If you change the nozzle manually, ALWAYS ensure that the nozzle is seated correctly and that you are
using the correct nozzle type.
If you have not inserted a nozzle or have used the wrong nozzle type, the program will prompt you to move
the placement head to the service position and change the nozzle. This error message will also appear if
you have not inserted the nozzle correctly.
If you insert the wrong nozzle or use the wrong nozzle type again, the gantry will move to the service posi-
tion once more after the reference sequence. The program will continue to prompt for a nozzle change
until you have obtained the correct configuration. If you do not succeed then proceed as follows:
– Switch off the station and cancel the program being sent to the station at the line computer.
– Rectify the nozzle error and restart the station.
TIP
Have the nozzles ready in a separate nozzle box - identify each compartment with the nozzle type and
color. This will prevent any confusion.
Do not raise used plastic nozzles. Just dispose of them immediately.
Fig. 6.3.1 Nozzle box
701
yellow
704
orange
705
red
711
yellow
SIPLACE 80S-20/F4/F4-6/F5 User’s Manual 6 What should you do ... ?
Edition 03/98 from Software Version SR.404.xx 6.4 When you change shift
6 - 9
6.4 When you change shift
Splice the tapes in good time so that the feeder modules will not run out of tape as soon as the new shift
starts. This can sometimes lead to pick-up errors and prolonged down-times.
Pass on information from one shift to the next if, for example, something has been changed in the place-
ment program or if frequent errors have occurred in certain feeder modules. Also take a look at the ’Feeder
module preliminary setup area' checklist in section 6.6, pages 6-12.
Carry out a set-up check.
Check that the feeder modules are equipped with the correct components and that they are at the correct
locations.
TIP
When you hand over the line, make sure that it as you would want to find it yourself, i.e. that
- The reject containers are empty.
- The waste containers are empty.
- The conveyor areas have been cleaned with a vacuum cleaner.
- Defective feeder modules in the feeder area have been replaced.