182050 User manual - 第217页

semi automatic &21680$ %/(5( 3/(1,6+0 (176 3$67(/2$ ',1* Software Version 07SP02 User Manual 8.9 W ARNING PROTECTI VE CLOTHING . APPROV ED PROTECTI VE CLOTHING SHOULD BE WORN BY SOLDER P AS TE AND SOL V ENT HA…

100%1 / 266
semi automatic
&21680$%/(5(3/(1,6+0(176
3$67(/2$',1*
8.8 User Manual Software Version 07SP02
b. The following window and menu bar is displayed.
9. Select Refill Paste (F1).
NOTE
If either the under screen cleaner paper or solvent are low or the Vortex
cleaning cassette has expired and are reported first, the refill paste option
is not displayed. In this case select Cancel until Refill Paste is displayed
in the menu bar.
The message ‘Select Load Cart to load the cartridge or exit to abort.’ is
displayed.
10. Select Load Cart. (F1).
The print carriage drives to the front of the machine and the dispenser rises
to the vertical position. A message is displayed on the screen ‘Open Cover
and Replace Paste Cartridge’.
11. To replace the paste cartridge carry out Steps 3-10 of Fitting a New Paste
Cartridge procedure, later in this section.
12. Repeat Steps 1, 2 and 13.
13. After the dispense routine has been completed, press Exit (F8).
Fitting a New Paste
Cartridge
It is necessary at intervals to fit a new paste cartridge into the paste dispenser.
If there is no cartridge in the dispenser or the cartridge is empty, the warning
window ‘Print Medium Low. Please Replenish.’ is displayed.
If the consumable action option in set preferences is set to suspend, the paste
dispenser is checked to ensure availability of paste, before allowing a print run
to start. If paste isn’t available the warning window ‘Print Medium Low. Please
Replenish.’ is displayed.
WARNING
SOLDER PASTE AND SOLVENTS. WHEN USING OR HANDLING ANY SOLDER
PASTE OR SOLVENT FORMULATION THE MANUFACTURERS’ RECOMMEND
SAFETY PRECAUTIONS MUST BE STRICTLY ADHERED TO.
Suspend on Warning
Print Medium Low. Please replenish.
Refill
Paste
Cancel
Refill
Paste
Cancel
Load
Cart.
Exit
Auto
Dispense
Manual
Load
Load
Cart.
Print
Directn
Exit
semi automatic
&21680$%/(5(3/(1,6+0(176
3$67(/2$',1*
Software Version 07SP02 User Manual 8.9
WARNING
PROTECTIVE CLOTHING. APPROVED PROTECTIVE CLOTHING SHOULD BE
WORN BY SOLDER PASTE AND SOLVENT HANDLERS AT ALL TIMES TO
ELIMINATE FUME INHALATION, EYE CONTACT, SKIN CONTACT AND
INGESTION.
To replace the paste cartridge carry out the following:
1. Press Paste Load (F3).
2. Press Load Cart. (F4).
The print carriage drives to the front of the machine and the dispenser rises
to the vertical position. A message is displayed on the screen ‘Open cover
and replace Paste Cartridge’.
3. Raise the printhead cover.
4. Remove the empty cartridge by unscrewing the cap at the rear of the paste
dispense tube to allow it to be withdrawn.
5. Unscrew the nozzle from the old cartridge and insert it into the new cartridge.
Run
Open
Cover
Paste
Load
Clean
Screen
Setup Monitor Maint.
Auto
Dispense
Manual
Load
Load
Cart.
Print
Directn
Exit
semi automatic
&21680$%/(5(3/(1,6+0(176
3$67(/2$',1*
8.10 User Manual Software Version 07SP02
6. Fit the new cartridge into the dispenser.
7. Screw the end cap onto the dispenser finger tight. Ensure the pneumatic
fitting on the cap is facing towards the rear of the machine.
8. Lower the printhead cover.
9. Press the System button.
10. Press Exit (F8).
Auto
Dispense
Manual
Load
Load
Cart.
Print
Directn
Exit