YSM20R_YSM20WR_Mainte_E - 第124页

3-63 3 Periodic maintenance items 5 Rotate heads -90°. 1. Close the machine safety cover and release the emergency stop. Attach the carriage if the machine is the carriage type. 2. Rotate heads -90° in the same manner as…

100%1 / 207
3-62
3
Periodic maintenance items
5.4 Cleaning shaft tip
When the shaft tip dirt is found in "3.4 Checking shaft tip" previously described, clean the shaft tip following
the procedure below.
5.4.1 HM head: Cleaning shaft tip
1
Remove nozzles from all heads.
With nozzle station:
1. Open [Unit] - [Head] screen.
2. Select desired head unit from "Table
Select".
3. Press the [Nozzle Change] button.
4. Select "ALL" for Head Number and select
"Store nozzle" for Nozzle type on "Nozzle
Change" screen.
5. Pressing the [OK] button stores nozzles of
all heads to the nozzle station.
n
NOTE
If the nozzle station is not equipped with the machine,
open the machine safety cover and remove nozzles
manually.
2
Move head unit to work position.
Press [Head Pos. Front] or [Head Pos. Rear]
button on "Setup" screen to move head unit
to convenient position for maintenance work.
TIP
When maintaining 2-beam head units, move the front
head unit to rear and move the rear head unit to front
to easily access to the head unit.
3
Rotate heads 90°.
1. Press [Axis] button on [Unit] - [Conveyor]
screen and select "ZR" tab.
2. Select desired head unit from "Table
Select".
3. Select "Head 1" from "Head Select".
4. Press [PTP] button for R (deg). Enter 90
and press [OK] button. Heads from No. 1
to 5 rotate 90°.
Heads from No. 6 to 10 rotate 90° by
selecting "Head 6" from "Head Select".
and enter 90.
e
5. Press the emergency stop button and
then open the machine safety cover. If
the machine is carriage type, detach
carriage to easily access to the head unit.
4
Clean shaft tip.
Apply ethanol to a cotton swab slightly and
clean shaft tip. Wipe the side of shaft with
twisted cotton swab.
TIP
Lower Z-axis joint block manually if difficult to clean
shaft tip.
Moving head unit
Step 2
[Head Pos. Front] button [Head Pos. Rear] button
54317-KMK-00
Rotating heads
Step 3
Enter 90°. Select head.
[PTP] button
Select table.
54318-KMK-00
Cleaning shaft tip
Step 4
Cotton swab
53399-KMK-00
3-63
3
Periodic maintenance items
5
Rotate heads -90°.
1. Close the machine safety cover and
release the emergency stop. Attach the
carriage if the machine is the carriage
type.
2. Rotate heads -90° in the same manner as
Step 3.
e
3. Press the emergency stop button and
then open the machine safety cover.
4. If the machine is carriage type, detach
carriage to easily access to the head unit.
6
Clean the back of shaft tip.
Clean the back of shaft tip in the same
manner as Step 4.
TIP
Lower Z-axis joint block manually if difficult to clean
shaft tip.
7
Check that shaft tips are clean.
Check that no dirt remains on shaft tips with
hand mirror.
Checking that shaft tips are clean
Step 7
Check all heads
Hand mirror
533A0-KMK-00
Rotating heads
Step 5
Enter -90°. Select head.
54319-KMK-00
3-64
3
Periodic maintenance items
5.4.2 FM head: Cleaning shaft tip
1
Remove nozzles from all heads.
With nozzle station:
1. Open [Unit] - [Head] screen.
2. Select desired head unit from "Table
Select".
3. Press the [Nozzle Change] button.
4. Select "ALL" for Head Number and select
"Store nozzle" for Nozzle type on "Nozzle
Change" screen.
5. Pressing the [OK] button stores nozzles of
all heads to the nozzle station.
n
NOTE
If the nozzle station is not equipped with the machine,
open the machine safety cover and remove nozzles
manually.
2
Move head unit to work position.
Press [Head Pos. Front] or [Head Pos. Rear]
button on "Setup" screen to move head unit
to convenient position for maintenance work.
TIP
When maintaining 2-beam head units, move the front
head unit to rear and move the rear head unit to front
to easily access to the head unit.
3
Rotate heads 90°.
1. Press [Axis] button on [Unit] - [Conveyor]
screen and select "ZR" tab.
2. Select desired head unit from "Table
Select".
3. Select "Head 1" from "Head Select".
4. Press [PTP] button for R (deg). Enter 90
and press [OK] button.
Select heads from No. 2 to 5 and enter
90 to rotate all heads 90°.
e
5. Press the emergency stop button and
then open the machine safety cover. If
the machine is carriage type, detach
carriage to easily access to the head unit.
4
Clean shaft tip.
1. Insert finger from opening of head unit
front cover to lower Z-axis joint block.
2. Apply ethanol to a cotton swab slightly
and clean shaft tip. Wipe the side of
shaft with twisted cotton swab.
Moving head unit
Step 2
[Head Pos. Front] button [Head Pos. Rear] button
54320-KMK-00
Rotating heads
Step 3
Enter 90°. Select head.
[PTP] button
Select table.
54321-KMK-00
Cleaning shaft tip
Step 4
Cotton swab
Lower here
with finger.
533A1-KMK-00